Javad DELTAGNSS Receiver Operator'S Manual Download Page 77

Page: 77 / 92

Appendix A

www.javad.com

PECIFICATIONS

This JAVAD GNSS product is a 216-channel GNSS receiver with a rugged magnesium housing
complete with TriPad and cable connectors.

Note:

Performance specifications assume a minimum of 6 GPS satellites above 15 degrees in elevation
and adherence to the procedures recommended in this manual.

Note:

In areas of high multipath, during periods of large PDOP, and during periods of increased
ionospheric activity, performance may degrade.

Note:

Use robust checking procedures in areas of extreme multipath or under dense foliage.

A.1. Receiver Specifications

The following sections provide specifications for the receiver and its internal components.

A.1.1. General Details

Table below lists the receiver’s general specifications.

Table A-1. Receiver General Specifications|

Physical

Enclosure

Aluminum extrusion, waterproof IP66

Color

JAVAD GNSS Green and Gray

Dimensions, mm

109 x 35 x 169

Weight, g
DELTAS-G2T
DELTAS-G3T, G3TAJ
DELTAD
DELTAQ

394
401
414
454

GNSS Antenna

External

Buttons

Two buttons:
Power – On/Off
Function (FN) – start/stop data logging.

Summary of Contents for DELTAGNSS Receiver




























































































Search results

Summary of Contents for DELTAGNSS Receiver

Reviews:

Related manuals for DELTAGNSS Receiver

Brands by name

Popular brands

Javad DELTAGNSS Receiver, Operator'S Manual

Search results

Summary of Contents for DELTAGNSS Receiver

Reviews:

Related manuals for DELTAGNSS Receiver

Brands by name

Popular brands