background image

Preface

Terms and Conditions

7

www.javad.com

     

 

 

         

                                                                                                                           

    

  

 

P

REFACE

Thank you for purchasing this product. The materials available in this Manual (the “Manual”)
have been prepared by JAVAD GNSS, Inc. (“JAVAD GNSS”) for owners of JAVAD GNSS
products. It is designed to assist owners with the use of the DELTA receiver and its use is subject
to these terms and conditions (the “Terms and Conditions”).

Note:

Please read these Terms and Conditions carefully.

Terms and Conditions

USE – JAVAD GNSS receivers are designed to be used by a professional. The user is expected to
have a good knowledge and understanding of the user and safety instructions before operating,
inspecting or adjusting. Always wear the required protectors (safety shoes, helmet, etc.) when
operating the receiver. 

COPYRIGHT – All information contained in this Manual is the intellectual property of, and
copyrighted material of JAVAD GNSS. All rights are reserved. You may not use, access, copy,
store, display, create derivative works of, sell, modify, publish, distribute, or allow any third party
access to, any graphics, content, information or data in this Manual without JAVAD GNSS’
express written consent and may only use such information for the care and operation of your
DELTA. The information and data in this Manual are a valuable asset of JAVAD GNSS and are
developed by the expenditure of considerable work, time and money, and are the result of original
selection, coordination and arrangement by JAVAD GNSS.

TRADEMARKS – DELTA™, JAVAD GNSS

®

 are trademarks or registered trademarks of

JAVAD GNSS. Windows

®

 is a registered trademark of Microsoft Corporation; Bluetooth

®

 word

mark is owned by the Bluetooth SIG, Inc. Product and company names mentioned herein may be
trademarks of their respective owners.

DISCLAIMER OF WARRANTY – EXCEPT FOR ANY WARRANTIES IN THIS MANUAL
OR A WARRANTY CARD ACCOMPANYING THE PRODUCT, THIS MANUAL AND THE
DELTA RECEIVER ARE PROVIDED “AS-IS.” THERE ARE NO OTHER WARRANTIES.
JAVAD GNSS DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR ANY PARTICULAR USE OR PURPOSE. JAVAD GNSS AND ITS
DISTRIBUTORS SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR

Summary of Contents for DELTAGNSS Receiver





























































































Reviews: