background image

Jason International, Inc.  •  

 

501.771.4477  

    

Page 17 of 17

    

Customer Service :  800.255.5766 

Copyright © 2013 Jason International.

IMPORTANT SAFETY INSTRUCTIONS

InsTruCTIOns PerTaInIng TO The rIsK Of fIre, eleCTrIC shOCK, Or InJurY 

TO PersOns.

This manual contains information and instructions for proper operation and maintenance of your hydrotherapy bath.  Failure to follow 
these instructions could result in personal injury, electrical shock, or fire.

warnIng: when using this unit, basic precautions should always be followed, including the following:

reaD anD fOllOw all InsTruCTIOns CarefullY

Danger:

 

TO reDuCe The rIsK Of InJurY fOllOw These PreCauTIOns: 

a.

  Do not permit children to use this product unless they are closely supervised at all times.

B.

  Use this unit only for its intended use as described in this manual. Do not use attachments not recommended by the manufac-

turer.

C.

  The water in a  hydrotherapy bath should never exceed 40°C (104°F). Water temperatures between 38°C (100°F) and 40°C 

(104°F) are considered safe for a healthy adult. Use time should be limited to approximately 30 minutes, followed by a shower 
to cool down. Longer exposures may result in hyperthermia. The symptoms of this condition are nausea, dizziness and fainting, 
and it can be fatal. Lower water temperatures are recommended for extended use (exceeding 10 -15 minutes) and for young 
children.

D.

  Since excessive water temperatures have a high potential for causing fetal damage during the early months of pregnancy, 

pregnant or possibly pregnant women should limit hydrotherapy bath water temperatures to 38°C (100°F).

e.

  The use of drugs or alcoholic beverages before or during hydrotherapy bath use may lead to unconsciousness with the 

possibility of drowning. Never use the hydrotherapy bath while under the influence of alcohol, anticoagulants, stimulants,  
antihistamines, vasoconstrictors, vasodilators, hypnotics, narcotics, or tranquilizers.

f.

  Persons with a medical history of heart disease, low or high blood pressure, circulatory system problems, or diabetes should 

consult a physician before using a hydrotherapy bath.

g.

  Persons using medication should consult a physician before using a hydrotherapy bath since some medication may induce 

drowsiness while other medication may affect heart rate, blood pressure, and circulation.

Danger:

 

 

To reduce the risk of injury, enter and exit the bath slowly. 

Do not operate this unit unless the suction cover is attached over 

the suction inlet fitting and the jet assemblies are installed.  There should be at least two (2) inches of water above the highest jet 
location during hydrotherapy bath operation.

 neVer run unIT DrY.

warnIng:

 

Never operate electrically connected devices in or near the bath. Never drop or insert any object into any opening.

This unit must be connected to a supply circuit that is protected by a GFCI. Such a device should be installed by a licensed electrician 
and should be tested on a regular basis (at least monthly). To test the GFCI push the 

TesT

 button. The GFCI should interrupt the 

power. Push the 

reseT

 button and the power should be restored. If the GFCI fails to operate in this manner, there is the possibility 

of an electric shock. 

DO nOT use. 

Disconnect the unit and have the problem corrected by a qualified service technician. 

To avoid the possibility of personal injury and discoloration of the acrylic surface, the inlet water temperature should not exceed 
40°C (104°F). The bath should be drained after each use. Each bather should start their bath with fresh water. Do not use oil base 
additives in your hydrotherapy bath.

CauTIOn: 

Do not use harsh abrasives or solvents for cleaning this unit.

InsTaller/Owner Bears all resPOnsIBIlITY TO COMPlY wITh all sTaTe  

anD lOCal CODes when InsTallIng ThIs PrODuCT.

 

 

Jason InternatIonal, Inc.

8328 MacArthur Drive  •  North Little Rock  •  Arkansas  •  72118-2029

www.jasoninternational.com 

Summary of Contents for Designer MicroSilk-AirMasseur


















Reviews: