background image

Jason International, Inc.  •  

 

501.771.4477  

    

Page 10 of 17

    

Customer Service :  800.255.5766 

Copyright © 2013 Jason International.

OPeRATING INSTRUCTION, FeATUReS, AND CONTROLS

INTRODUCTION

This manual contains all of the information needed for the 
proper installation and operation of your Jason MicroSilk

®

AirMasseur

®

 bath. The bath has been designed to give 

you years of relaxing trouble-free service, provided the 
unit is maintained and operated in accordance with these 
instructions. 

Thoroughly clean and disinfect the unit as described in 
the 

CLeANING

 section of the 

USeR MAINTeNANCe 

INSTRUCTIONS

 section of this owner’s manual before its 

first use and periodically thereafter. 

CAUTION: 

Keep hair, towels, and clothing away from the 

suction fitting whenever the equipment is On. Never operate 
the equipment with the suction cover off, as doing so voids 
the manufacturer’s warranty. It is a safety cover designed to 
eliminate the potential of hair and body entrapment. 

All Jason MicroSilk

®

-AirMasseur

®

 baths are pre-plumbed at 

the factory. 

WARNING: Before operating refer to the instructions at 

the end of this owner’s manual pertaining to the risk of 

fire, electric shock, or injury to persons.

FeATUReS AND CONTROLS

STANDARD AND PReMIeR eDITION  

MICROSILK

®

-AIRMASSeUR

®

The Jason Standard Edition MicroSilk

®

-AirMasseur

®

 bath 

provides both a Microbubble generator unit and an air bath 
system. The air bath system includes a variable-speed, 
1-HP air blower with heater and three (3) massage modes: 
Continuous, Wave, or Pulse; an electronic control with a 
low water-level sensor to prevent the MicroSilk

®

 pump from 

operating without water; and a 20-minute timer.

 

The Jason Premier Edition MicroSilk

®

-AirMasseur

®

 bath 

provides all the features of the Standard Edition with the 
included benefits of a LED Chromatherapy Mood Light, and 
an Ozone Sanitation system. 

 

Standard/Premier Touchpad

One main control touchpad mounted on the bath deck 
features several icons used by the bather to control the 
MicroSilk unit, blower, and LED mood light. A built-in timer 
shuts the pump off 20 minutes after being activated.

SIGNATURe eDITION 

MICROSILK

®

-AIRMASSeUR

® 

The Jason Signature Edition MicroSilk

®

-AirMasseur

®

 bath 

includes both a Microbubble generator unit and an air bath 
system. The air bath system includes a variable-speed, 
1-HP air blower with heater and three (3) massage modes: 
Continuous, Wave, or Pulse. The system also includes a 

Chromatherapy mood light, Automatic Ozone System that 
will be operated any time the blower is powered; a digital 
control with LCD display window; low water and temperature 
sensors; and a 20-minute timer.

 

Signature Touchpad

A main control touchpad mounted on the bath deck features 
an LCD readout which alternately indicates the water 
temperature (+/- 5°F) and time remaining. The Signature 
Edition touchpad allows the bather to control the MicroSilk

®

 

unit, blower, and LED mood light. A built-in timer shuts off 
the pump 20 minutes after being activated. 

 

Signature Remote Control

In addition to the main control touchpad installed on the bath 
deck, a floating, waterproof Universal Remote Control is 
provided with all Signature Edition MicroSilk

®

-AirMasseur

®

 

baths. This remote control provides the same control 
functions as the bath’s main control console, plus the bather 
may remotely operate a TV, DVD, VCR, CD, etc. Refer to 
the Instruction Manual provided with the remote control for 
detailed instructions.

 

Jets

A strategically placed MicroSilk

®

 jet is provided for complete 

enjoyment of your bath. 

 

Pumps

Pumps provided on Jason baths are factory tested when 
assembled and retested after installation on the bath. These 
pumps are of efficient design incorporating high-quality long-
life seals which provide superior service. However, should 
the pump need service, suction barbs and discharge unions 
are provided for easy pump removal.

 

MicroSilk Unit

The MicroSilk

®

 unit generates oxygen-rich microbubbles 

that fill the bath. MicroSilk

®

 units provided on Jason baths 

are factory tested when assembled and again retested after 
installation on the bath.

 

Blower

The blower generates warm air and pushes it through the 
air jets. Blowers provided on Jason AirMasseur

®

 baths are 

factory tested when assembled and again retested after 
installation on the bath. 

 

Standard / Premier edition Automatic Purge

Fifteen (15) minutes after the control has shut off and the 
bath is completely drained, the blower will start again for a 
two-minute purge cycle that dries the air channel. Note that 
the blower light will flash during the 15-minute pause before 
the purge cycle begins. Once the purge cycle begins, all 
indicators will light and the keypad operation will be disabled 
for two (2) minutes.

Summary of Contents for Designer MicroSilk-AirMasseur


















Reviews: