Jason International, Inc. •
501.771.4477
Page 13 of 18
Customer Service : 800.255.5766
Copyright © 2011 Jason International.
OpERAtinG instRuctiOn, FEAtuREs, AnD cOntROLs
intRODuctiOn
This manual contains all information needed for the proper
installation and operation of your Jason Whirlpool bath. The
bath has been designed to give you years of relaxing trouble-
free service, provided the unit is maintained and operated in
accordance with these instructions.
Thoroughly clean and disinfect the unit as described in the
CleanIng
section of the
user MaInTenanCe InsTruCTIOns
of this owner’s manual before its first use and periodically
thereafter.
All Jason whirlpool baths are pre-plumbed at the factory.
warnIng: Before operating refer to the instructions pertaining to the
risk of fire, electric shock, or injury to persons.
stAnDARD AnD pREmiER EDitiOn WHiRLpOOL
The Jason Standard Edition Whirlpool bath system includes
a quiet 1 1/2-HP, 1 speed pump (or two each 1-HP, 1-speed
pumps on the LS640); an electronic control with a low water
level sensor to prevent the pump from operating without water;
and a 20-minute timer.
The Jason Premier Edition Whirlpool bath provides all the
features of the Standard Edition with the included benefits
of a 1 1/2-HP, 1 speed pump combination pump/heater,
LED Chromatherapy Mood Light, and an Ozone Sanitation
system.
standard/premier touchpad
One main control touchpad mounted on the bath deck contains
several icons used by the bather to control the pump, and LED
mood light. A built in timer shuts the pump off 20 minutes after
being activated.
siGnAtuRE EDitiOn WHiRLpOOL
The Jason Signature Edition Whirlpool bath system includes
a quiet 1 1/2-HP, 3 speed pump (also a 1-HP secondary pump
on the LS640); Automatic 1.5kW Heater, Chromatherapy mood
light, Automatic Ozone System that will be operated any time
the pump is powered; a digital control with LCD display window;
low water and temperature sensors; and a 20-minute timer.
signature touchpad
A main control touchpad mounted on the bath deck features a
LCD readout which alternately indicates the water temperature
(+/- 5°F) and time remaining. The Signature Edition touchpad
allows the bather to control the pump, LED mood light and
optional jetted neck pillow. A built in timer shuts the pump off
20 minutes after being activated.
signature Remote control
In addition to the main control touchpad installed on the
bath deck, a floating, waterproof Universal Remote Control
is provided with all Signature Edition Whirlpool baths.
This remote control provides the same control functions
as the bath’s main control console, plus the bather may
remotely operate a TV, DVD, VCR, CD, etc. Refer to the
Instruction Manual provided with the remote control for
detailed instructions.
Jets
Strategically placed whirlpool jets are provided for complete
enjoyment of your bath. The jets are specially designed
for maximum whirlpool action with either directional or
rotational capabilities. By changing the direction of the jets,
you can concentrate the massaging jet stream to your area
of preference. You can also individually adjust the flow of
each whirlpool jet.
Air Volume control
Two air controls are conveniently located for bather control.
Turning the knob counter-clockwise increases the air flow
and turning the knob clockwise decreases the air flow. For
maximum whirlpool effect, open the air controls completely.
Restriction of the air controls will produce fewer air bubbles
and a reduction in hydrotherapy performance.
pumps
Pumps provided on Jason baths are factory tested when
assembled and retested after installation on the bath. These
pumps are of efficient design incorporating high quality long
life seals which provide superior service. However, should
the pump need service, suction barbs and discharge unions
are provided for easy pump removal.
Filing And Draining
Close the drain and fill the bath with water at least two (2)
inches (50mm) above the jets. The inlet temperature should
not exceed 40°C (104°F) as this could damage the acrylic
surface. When bath is in use, turn the unit Off before draining
the water. The bath unit and its plumbing are designed to
drain after each use whether used as a hydrotherapy bath,
soaking bath, or just taking a shower.
NOTe:
If the unit fails to operate, check the breaker panel
to insure that the circuit breaker is on. Check the GFCI by
testing and resetting it. Also check the water level in the
bath; it must be above the water level sensor located on the
sidewall of the bath for the pump to operate. If the unit still
fails to operate, refer to the Trouble Shooting Guide section
of this manual. If the unit still fails to operate and is out of
warranty, contact an authorized service technician for repair.
If the unit is within the warranty period, contact JASON
Technical Services at 800-255-5766. DO NOT ATTEMPT
TO RESOLVE THE PROBLEM.
FeAtures AnD Controls
