manualshive.com logo in svg

J&J Amusements Can-Am, Service Manual, Page: 68 / 272

Share
Download
J&J Amusements Can-Am Service Manual Download Page 68

4-6

GO

-KARTS

B

U

MPERBOAT

S

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

TM

 STEERING ADJUSTMENTS - TOE

Using a C-clamp, lock the steering shaft in the 
center position. This can be done by clamping two 
D-rubber plates to the steering shaft, or by using a 
Angle iron to lock the steering shaft.

NOTE:
The steering shaft must be at the center position 
before toe can be set correctly.

Now from the front of the spindle (facing the front 
of the go-kart), measure the distance from the frame 
rail to the straight edge.

Subtract the measurement reading from the rear of 
the spindle to the measurement reading received 
from the front of the spindle; this measurement 
equals the toe-in.

Standard tow-in is 0”-1/8” with a service limit of 
1/4” of total toe-in.

Place a straight edge across hub flange.
From the rear of the spindle (facing the rear of go-
kart), measure the distance from the frame rail to 
the straight edge.

Angle iron

KEEP THOSE NUTS AND BOLTS SECURELY FASTENED WITH LOCTITE!

Loctite Threadlocker 10ml bottle (blue) #3-20-0001

Summary of Contents for Can-Am

















































































































































































































































































Reviews:

No comments