manualshive.com logo in svg

J&J Amusements Can-Am, Service Manual, Page: 34 / 272

Share
Download
J&J Amusements Can-Am Service Manual Download Page 34

All go-karts leave J&J Amusements with warning decals in place. All warning decals must 

be legible. If any warning decal cannot be read you must replace it immediately. J&J carries 

all the decals you need. See section 12 for decals placement locations.

 WARNING    DECALS

DO N

OT REMOVE THIS DE

CA

L

DO N

OT REMOVE THIS DE

CA

L

#00979

#00978

#00180

WARNING!

Go-karts have rotating parts.

Hair longer than

shoulder length

must be secured

above shoulder.

Serious injury or 

death could occur!

DO NOT REMOVE THIS DECAL

#1-60-0288

#1-60-0388

#001711

#001712R

#1-60-0020

#00981

#00980

BRAKE

GAS

DO NOT REMOVE THIS DECAL.

!

TO HELP PREVENT

INJURY OR DEATH

All pads and guards must be

maintained and in place during

operation of this device.

DO NOT REMOVE THIS DECAL

WARNING

GASOLINE IS EXTREMELY FLAMMABLE AND IS EXPLOSIVE UNDER CERTAIN 
CONDITIONS.

REFUEL IN A WELL-VENTILATED AREA WITH ENGINE STOPPED.
DO NOT SMOKE OR ALLOW FLAMES OR SPARKS IN THE AREA WHERE THE 
ENIGINE IS REFUELD OR WHERE GASOLINE IS STORED.

DO NOT OVERFILL THE TANK (THERE SHOULD BE NO FUEL IN THE FILLER 
NECK). AFTER REFUELING, MAKE SURE THE FUEL CAP IS CLOSED 
SECURSLY AND VENT OPEN.

BE CAREFUL NOT TO SPILL FUEL WHEN REFUELING. SPILLED FUEL OR FUEL 
VAPOR MAY IGNITE. IF ANY FUEL IS SPILLED, MAKE SURE THE AREA IS DRY 
BEFORE STARTING THE ENGINE.

NEVER REFUEL WHEN RIDERS ARE PRESENT.

J&J Amusements, Inc. 1(800) 854-3140

DANGER

Hair longer than shoulder 

length must be secured 

above shoulder.

Keep arms and legs in kart 

at all times.

BRAKE

GAS

DO NOT REMOVE THIS DECAL.

WARNING

The Engine Exhaust from this product

contains chemicals known to the State 

of California to cause cancer, birth 

defects or other reproductive harm.

Do not remove this decal

!   WARNING

Must meet posted height requirement.
Shoes and shirt must be worn.
All loose clothing must be secured.
Hair longer than shoulder length must be secured above shoulder length.
Keep both hands on steering wheel and both feet in kart at all times, unless
otherwise instructed by attendant.
One person per restraint.
Restraint must be worn at all times when in kart.
Do not bump, skid or slide karts.
Riders must remain seated at all times unless instructed by attendant.
No one under the influence of drugs or alcohol is allowed to ride.
This ride is not recommended for individuals who have heart problems, neck
or back problems, or pregnant women.
Participate at your own risk.

Part Number

001712R

DO NOT REMOVE THIS DECAL.

WARNING

Keep Hands And

Arms In Car

At All Times.

DO NOT REMOVE THIS DECAL

Summary of Contents for Can-Am

















































































































































































































































































Reviews:

No comments