manualshive.com logo in svg

J&J Amusements Can-Am, Service Manual, Page: 140 / 272

Share
Download
J&J Amusements Can-Am Service Manual Download Page 140

7-26

GO

-KARTS

B

U

MPERBOAT

S

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

TM

Re-assemble the brake drum/hub with the 7/16” jam 
nuts and 5/32” Allen-head shoulder bolts.

Torque the bolts to 11 ft/lbs.

Slide the brake drum/hub assembly over the newly 
installed brake shoes until the drum stops at the backing 
plate. Pull the drum assembly out 1/16” from the 
backing plate so the drum does not drag on the backing 
plate.

Re-install the 5/16” Allen bolt into the hub and torque 
to 50 ft/lbs.

Re-install the floater hub/drum assembly over the axle. 
Secure the floater hub/drum assembly with the axle 
collar and axle nut, and torque the axle nut to 50 ft/lbs.

Re-install any split collars that may have been removed.

Re-install the rear wheel.

REPLACEMENT BRAKE DRUMS AVAILABLE.

Rear brake drum # F030F01-43520-0

Summary of Contents for Can-Am

















































































































































































































































































Reviews:

No comments