manualshive.com logo in svg

J&J Amusements Can-Am, Service Manual, Page: 194 / 272

Share
Download
J&J Amusements Can-Am Service Manual Download Page 194

12-2

GO

-KARTS

B

U

MPERBOAT

S

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

TM

Rubber “T”  bushings are made to collapse slightly 
under pressure from tightening the mounting nuts.  
These “T” bushings fit over the mounting studs that 
are part of the frame.

NOTE: Do not overtighten; snug the mounting nuts 
to capture the body only. 

Rubber  latches or bungees are often used to hold 
bodies, while providing for isolation movement.

NOTE: Failure to use body latches will result in 
excess body damage.

Bodies settle over time, so rubber mounting 
bushings, bumpers, plates, etc must be adjusted to 
best support the body.  Use adjustable stand-offs 
and washers under the rubber bumpers or brackets 
to keep the bodies mounted firmly.

Set screw

Latch

T bushing

Adjustment

MOTION PRO “ONE MAN” 
BRAKE BLEEDER, ONE WAY 
VALVE!

Hydraulic brake bleeder
#3-96-0010

Summary of Contents for Can-Am

















































































































































































































































































Reviews:

No comments