manualshive.com logo in svg

J&J Amusements Can-Am, Service Manual, Page: 208 / 272

Share
Download
J&J Amusements Can-Am Service Manual Download Page 208

13-4

GO

-KARTS

B

U

MPERBOAT

S

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

TM

IF THE SWITCH BOX HAS A PROBLEM, DO I NEED TO REPLACE IT? 

In many cases, when a switch box has a problem, it can be easily fixed. The switches used are heavy-duty and should last 
a long time; often, when there is a problem, the cause is related to a loose or broken wire at the switch.

CAN THE BUTTONS BE REPLACED? 

Yes, the red or black switch buttons can be replaced. The red “stop” button is J&J part number 1-15-0052; the black 
forward/reverse switch is J&J part number 1-15-0057.

IF THE LINEAR THROTTLE POTENTIOMETER FAILS, HOW WILL I KNOW? 

If the linear throttle potentiometer fails, the symptoms can vary depending on how it failed internally. One possible failure 
can cause a 6-flash code on the controller. The 6-flash code indicates that the controller is not “seeing” the linear throttle 
potentiometer in the system. Possible causes can be the power going to the linear throttle controller, the linear throttle 
controller failing, or the path of the signal going from the linear throttle controller to the main controller. The easiest way to 
rule out the linear throttle controller as the problem is to unplug the existing unit from the interconnect board and plug into 
a working linear throttle controller (see page 13-20). If the linear throttle controller was the problem, the flash code should 
stop and the kart will operate. If the controller fails internally, however, the controller still sees it as part of the system; the 
controller will not have a flash code, but when the gas pedal is depressed, the kart will not move. If this is the case, the 
same procedures should be followed. Replace the existing linear throttle controller with a working unit.

WHAT WILL ALERT ME THAT THE MOTOR CONTROLLER HAS FAILED? 

The controller can fail and show a flash code or completely stop working and show no flash code at all. 

CAN THE MOTOR CONTROLLER’S PROFILE BE ADJUSTED? 

Yes, this can be done via PC interface. Contact J&J’s service department for instructions.

CAN THE MOTOR CONTROLLER BE REPAIRED? 

No, the controller cannot be repaired.

CAN THE REMOTE SHUT DOWN SYSTEM BE REPAIRED? 

Yes, the components can be sent back to the manufacturer for repair.

Summary of Contents for Can-Am

















































































































































































































































































Reviews:

No comments