Home
/
J&J Amusements
/
Can-Am
/
Service Manual

J&J Amusements Can-Am, Service Manual, Page: 102 / 272

Share

Page: 102 / 272

J&J Amusements Can-Am Service Manual Download Page 102

6-16

GO

-KARTS

B

U

MPERBOAT

S

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

TM

AXLE BEARING REMOVAL

The positive lock bearing grips evenly and tightly to the axle shaft, preventing problems that arise with other types of
systems. The tapered inner sleeve slides over the shaft and is threaded and split. The split is wide at one end to index
the locking ring. The bearing inner race inside diameter (i.d.) is tapered to match the outside diameter (o.d.) of the split
sleeve.

The lock ring is installed with the “bent” tabs facing the jam nut, and indexed by the inner tab to the tapered sleeve.
The jam nut is beveled on the side facing the lock ring. Using the spanner wrench (J&J part# 1-60-0193), tighten the
jam nut, which draws the tapered sleeve against the tapered inner race and collapses the sleeve tightly to the axle’s
shaft over its full contact area.

It is a good idea to tighten the lock nut snugly, then tap the sleeve on the opposite side of the jam nut to help seat
the taper, then tighten again. Repeat as needed until it is tight, then check with a torque wrench to obtain the proper
torque reading of 45ft lbs.

When secure, bend over two of the appropriately-aligned locking tabs into the cut-outs on the o.d. of the jam nut.
When properly installed, this system will not spin on the shaft as long as the bearing is in good working order.

Tapered sleeve

Jam nut

Lock ring

Bearing

OVERVIEW

«
...
100
101
102
103
104
...
»

Summary of Contents for Can-Am

















































































































































































































































































Reviews:

No comments