manualshive.com logo in svg

J&J Amusements Can-Am, Service Manual, Page: 195 / 272

Share
Download
J&J Amusements Can-Am Service Manual Download Page 195

12-3

GO

-KARTS

B

U

MPERBOAT

S

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

TM

The reinforced fiberglass body rests on rubber 
bumpers that support and isolate the body from the 
frame. Eye bolts are used to secure the hold-down 
straps.

Bumpers are bolted to the mounting brackets and 
are easily replaced if damaged.

The side of the F-22 body is rubber-mounted to the 
frame, just in front of the rear wheels.

NOTE: Make sure the rubber “well” nut is in place 
to isolate the body from the frame.

 BODY  MOUNTS - F-22 GO-KART

Eye bolts

Bumper

Bumper

SIMPLE, EASY OIL EXTRACTION. JUST INSERT THE SUCTION TUBE 
INTO THE CRANKCASE FILLER NECK AND GIVE IT A FEW PUMPS TO 
START THE SUCTION.

Hand operated oil extractor #5958434

Summary of Contents for Can-Am

















































































































































































































































































Reviews:

No comments