JAI SW-4000TL-10GE, User Manual

Page: 46 / 64

Setting range Default value Description
Configure image capture settings.
Single Frame, Multi
Frame, Continuous Countinuous Select the image capture mode.
ー ー Start image capture.
ー ー Stop image capture.
1〜65535 1 In [MultiFrame] mode, set the number of frames to capture.
ー 66 Display the frame rate as a frequency. (unit: Hz)
66 〜 66 Set the AcquisitionLineRate (Hz).
The maximum value varies depending on the PixelFormat and ROI settings.
ー Acquisition Start Select the trigger operation.
[Setting range]
Acquisition Start, Acquisition End, Line Start, Frame Start, Frame Transfer Start
TriggerMode Off, On Off Select the trigger mode.
TriggerSource ー Line4 TTL In 1 Select the trigger signal source.
[Setting range]
PulseGenerator0, PulseGenerator1, PulseGenerator2, PulseGenerator3
UserOutput0, UserOutput1, UserOutput2, UserOutput3
Action 0, Action 1, Action 2, Action 3
Line4 TTL In 1, Line5 Opt In 1, Line10 TTL In 2, Line13 TTL In 3
Logic Block 0, Logic Block 1, Encoder Trigger
TriggerActivation RisingEdge, FallingEdge,
Level High, Level Low Rising Edge Select the polarity of the trigger signal
(i.e., location of signal at which trigger is applied).
[Trigger Selector] = Line Start
ExposureMode is Off or Timed : RisingEdge, Falling Edge
ExposureMode is TriggerWidth : LevelHigh, LevelLow
Off, Timed,
Trigger Width Timed Select the exposure mode.
3 〜 15149 Set the exposure time.
Setting range Default value Description
Set whether to enable auto exposure.
Off, On Off In IndividualGainMode, R, G, B can be configured individually for the entire
gain adjustment range of the sensor.
ー ー Select the gain to configure.
[Setting range]
IndividualGainMode : On DigitalGreen, DigitalRed, DigitalBlue
IndidualGainMode : Off DigitalAll, DigitalRed, DigitalBlue
Gain ー x1.0 Set the gain value for the gain setting selected in [GainSelector].
[Setting Range]
IndividualGainMode : On
DigitalGreen : x1.0 〜 x16.0
DigitalRed: x1.0 〜 x16.0
DigitalBlue: x1.0 〜 x16.0
IndidualGainMode : Off
DigitalAll: x1.0 〜 x8.0
DigitalRed: x0.4 〜 x4.0
DigitalBlue: x0.4 〜 x4.0
x1(0dB), x2(6dB),
x4(12dB) x1(0dB) Set the gain value for the analog gain setting selected in [Analog Gain Selector].
All, Red, Blue All Select the black level to configure.
BlackLevel DigitalAll -133〜255
DigitalRed -64〜 64
DigitalBlue -64〜 64 DigitalAll 0
DigitalRed 0
DigitalBlue 0 Set the black level value.
Off,
Once,
Preset5000K,
Preset6500K,
Preset7500K Off Enable/disable auto white balance.
16〜4096 step 16 4096 Set the area for adjusting white balance.
0 〜 4080 step 16 0 Set the area for adjusting white balance.
ー Idle Display the result for adjusting white balance.
0:Idle
1:Succeeded
2:Error1 - G image was too bright
3:Error2 - G image was too dark
4:Error3 - Timeout
0.45, 0.5, 0.55, 0.6, 0.65,
0.75, 0.8, 0.9, 1.0 0.45 Set the gamma value.
Off, Gamma, LUT Off Select the LUT mode.
Acquisition Frame Count
ExposureMode
Balance White Auto Width
Balance White Auto OffsetX
Balance White Auto Result
LUTMode
Gamma
Trigger Selector
Acquisition Frame Rate(Hz)
d） Analog Control
Item
AnalogBaseGain
Acquisition Line Rate
Item
Acquisition Stop
Acquisition Start
c） Acquisition Control
GainSelector
Balance White Auto
BlackLevelSelector
ExposureTime
IndividualGainMode
Acquisition Mode
SW-4000TL-10GE
— 4 6 —