JAI Go-X Series, User Manual

Page: 73 / 88

Setting range Default value Description
Configure sequencer settings.
Off, On Off Enable/disable [SequencerMode].
0:TriggerSequencerMode,
1:CommandSequencerMode TriggerSequencerMode Select the sequencer mode.
1〜32 1 Select the index number to configure.
SequencerWidth ー ー Set the width of the selected SequencerIndex.
SequencerHeight ー ー Set the height of the selected SequencerIndex.
SequencerOffsetX ー ー Set the horizontal offset value for the selected SequencerIndex.
SequencerOffsetY ー ー Set the vertical offset value for the selected SequencerIndex.
SequencerFrameCount ー ー Set the FrameCount value for the selected SequencerIndex.
SequencerExposureTime 1μs 〜 ー Set the exposure time for the selected SequencerIndex.
SequencerGainAnalogAll x1.0 〜 x16.0 x1.0 Set the GainAnalogAll value for the selected SequencerIndex.
SequencerGainDigitalRed x0.447〜x5.624 x1.0 Set the DigitalRed Gain value for the selected SequencerIndex.
SequencerGainDigitalBlue x0.447〜x5.624 x1.0 Set the DigitalBlue Gain value for the selected SequencerIndex.
SequencerLutEnable True, False False Set the LutEnable value for the selected SequencerIndex.
SequencerSetNext 0 〜 32 Set the next index to be displayed for the selected SequencerIndex.
(Enabled only for TriggerSequencer.)
If 0 is specified, the operation of Sequencer is stopped.
1〜255 1 Set the repeat count for the sequencer.
1〜32 1 Displays the sequencer set number.
1〜32 1 Specify the first index number to switch to when starting
[TriggerSequencerMode].
1〜32 1 Set this to change the SequencerIndex.
(Enabled only for CommandSequencer.)
ー ー In [TriggerSequencerMode], reset the current index number to the number
configured in [SequencerSetStart].
Configure shading correction settings.
0:Flat Shading
1:Color Shading 0:Flat Shading Select the shading correction method.
0:Off, 2:User1
3:User2, 4:User3 0:Off Set the area to which to save shading correction data.
When this is set to [Off], shading correction data is not saved.
ー ー Execute shading correction.
This command can not be executed under the following conditions.
・When no image is output
・Outputting TestPattern
・In Sequencer mode
・When the ROI setting is under the following conditions
(Width or Height is less than 128)
・In Decimation mode
・In Binning mode
ー ー Display the shading correction results.
[results]
0: Condition Error, 1: TooDark, 2: TooBright, 3: Correction Limit, 4: Complete
Configure counter settings.
(This camera only supports counter functions.)
0:Counter0, 1:Counter1,
2:Counter2, 3:Counter3 ー Select the counter.
CounterEventSource Counter0
0:Off, 1:FrameTrigger
Counter1
0:Off, 3:SensorReadOut
Counter2
0:Off, 2:ExposureStart
Counter3
0Off, 4:FrameTransferEnd Off Assign the counter event signal for which you want to read the count value to
a dedicated counter, and read the value.
CounterEventActivation ー ー Set the count timing.
The setting value is fixed with the following data.
Counter0:RisingEdge, Counter1:RisingEdge, Counter2:RisingEdge, Counter3:FallingEdge
CounterReset ー ー Reset the counter.
CounterRefresh 0〜65535 0 Update the count value.
CounterValue 0〜65535 0 Display the count value.
CounterStatus ー ー Display the counter status.
0:CounterIdle: Idle
2:CounterActive: Counting
4:CounterOverflow: Count value exceeded the mazimum value
Configure settings for other JAI functions.
Off, On Off Enable/disable VideoProcessBypass mode.
r) ImagingControl
VideoProcessBypassMode
ShadingDetectResult
PerformShadingCalibration
ShadingMode
ShadingCorrectionMode
CounterSelector
Item
SequencerControl
SequencerMode
SequencerModeSelect
SequencerSetSelector
SequencerRepetition
SequencerSetActive
SequencerSetStart
SequencerCommandIndex
SequencerReset
q) CounterAndTimerControl
p) ShadingConrol
— 73 —
Go-X Series GigE Vision I/F