AD-081CL
- 48 -
11.2
Specifications Table
Specifications
AD-081CL
Scanning system
Progressive scan
Frame Rate Full scan
30 frames/sec. Progressive (768 lines/frame)
High Frame Rate mode : 60 frames / sec. (768 lines/frame)
Pixel clock
33.75MHz
Line frequency
23.768 KHz (1420 pixel clocks/line)
Image sensor
1/3 inch Monochrome IT CCD
(
ICX204AL)
Sensing area
4.76 (H) x 3.57 (V) mm (1/3 inch diagonally)
Cell size
4.65 (H) x 4.65 (V) µm
Active pixels
1024(H) x 768 (V)
Pixels in Video output
Full
1/2 Partial
1/4 Partial
1/8 Partial
V Binning
1024 (h) x 768 (v) 30fps/60fps H = 23.768 kHz
1024 (h) x 384(v) 48fps/96fps H = 23.768 kHz
1024 (h) x 192 (v) 68 fps/136fps H = 23.768 kHz
1024 (h) x 96 (v) 86fps/172fps H = 23.768Hz
1024 (h) x 384 (v) 49.5 fps/99fps H= 19.622 KHz
Minimum Sensitivity on sensor
1.1 Lux
Max. Gain, Shutter OFF, 50% Video Level
S/N ( dB)
More than 54dB (0dB gain)
Iris video output, Analogue
0.7 V p-p (without Sync)
Digital Video Output
Via Camera Link connector 1
BM1_10bit, BWBW2_10bit, BW1_8bit, BBW2_8bit
Via Camera Link connector 2
BM2_10bit, BWBW1_10bit, BW2_8bit, BBW1_8bit
Note: Synchronized or separate output is selectable.
Input signal
Trigger
（
TTL/75
Ω）
x
2
via Camera Link or HIROSE
12P
Output signal
Hirose 12P XEEN
（
TTL/75
Ω）
x 2
Camera Link 1,2: EEN
、
FVAL
，
LVAL
，
DVAL
，
PCLK
(LVDS)
Gain
Master Gain:
-3dB
～
+12dB
Knee compensation
Knee point, Knee slope ( 10bit/8bit)
Gamma
1.0 fixed
Shading compensation
ON/OFF
Auto luminance balance
Gain setting range: -3dB to +6dB (High Frame Rate mode)
Detection area is selectable from 9 divisions.
Synchronization
Int. X-tal
Trigger mode
Pre-select, Pulse width and PIV mode
Accumulation
LVAL synchronous or LVAL a-synchronous automatic selection
Preset shutter speed
11steps:
OFF(1/30),1/60,1/100,1/120,1/250,1/500,1/1000,1/2000,
1/4000,1/10,000,1/16,000,1/50,000 sec.
Programmable exposure
0.5 L to
792L
(1 LVAL unit)
Pulse width control
1/10,000 sec. to 2 seconds
Control interface
Camera Link x 2
（
EIA-644 LVDS
）
Effective for the first established communication port
Lens Mount
C Mount
（
Rear protrusion on C mount lens must be less than 4mm
）
The lens should be designed for 3CCD cameras
Operating temperature
-5
C to +45
C
Operating humidity
20 to 80% ( non-condensing )
Storage temperature/humidity
-25
C to +60
C/20%
～
80%
(non-condensing)
Vibration
3G (15Hz to 200Hz XYZ)
Shock
50G
