background image

IO-14

Jade Range LLC 

– A Middleby Company

Titan

TM

 Series Heavy Duty Range

Model Series JTRH & JTRHE

Convection Oven Re-Igniter
(Electronic Ignition)

NOTE:

 In order for the re-Igniter to operate, the

master (power) switch located at the top of the
oven panel must be in the ON position.

If the pilot light is extinguished by drafts or
temporary loss of gas pressure from air in lines,
the re-igniter will immediately attempt to re-light
the pilot.

If the pilot fails to light, the thermocouple will cool
(usually within 30 seconds) and shut the gas off to
the burner. This will require that the pilot light be
re-lit manually.

Turn the oven gas valve to the OFF position. Wait
5 minutes. Then repeat steps 1-10 above to re-
light pilot.

CONVECTION OVEN OPERATION

WARNING

THE OVEN AND ITS PARTS ARE HOT.
USE CARE WHEN OPERATING, CLEANING,
OR SERVICING THE APPLIANCE.

1.

Turn on the master power switch.

2.

Turn the oven gas valve to ON.

3.

Set thermostat to the desired temperature.

4.

Turn fan switch to AUTO. (This will turn on the
fan.)

5.

Allow oven to pre-heat to the desired
temperature. (12-16 minutes.)

6.

Open oven door. (Fan will automatically stop.)

7.

Place product into oven leaving space all
around for even heating.

8.

Close oven door. (Fan will turn on and oven
will begin baking.)

NOTE: 

Placing the fan switch to MANUAL will

allow the fan to run when the oven door is opened
to rapidly lower the oven temperature.

Convection Oven Controls

Power Switch

Master power switch for the convection oven.

Power On Light

Light will illuminate when the oven is operating.

Blower Auto/Manual Switch

Toggle switch that controls the mode for the
blower.

AUTO

 – Normal mode. Allows for automatic

operation of the blower (fan shuts off when
door is opened).

OFF – 

Turns the blower off. Used for limited

cooking of certain products.

MANUAL

 – Used to rapidly cool the oven to

accommodate cooking of another product at a
lower temperature setting. Or in the event of a
door switch failure fan will still operate but fan
will stay on with door open

Oven Thermostat

Used to set the desired cooking temperature for
the oven.

Summary of Contents for JTRH Series





















Reviews: