background image

IO-13

Jade Range LLC 

– A Middleby Company

Titan

TM

 Series Heavy Duty Range

Model Series JTRH & JTRHE

French Top Range Controls

1.

Check that pilot lights are lit.

2.

Turn valve to ON position. (Burner will light.)

3.

Adjust flame to desired height.

4.

To turn off, move control to the OFF position.

LIGHTING OVEN PILOT LIGHT

Standard Oven

BEFORE LIGHTING PILOT LIGHT FOR OVEN,
LIGHT ALL PILOTS FOR TOP BURNERS

1.

Remove the oven kick plate.

2.

Turn the oven gas valve to OFF.

Figure 12: Griddle Models

Gas Valve Location

3.

Turn the oven thermostat to OFF.

4.

Push and hold down the red button on the pilot
valve to light the pilot light. Continue to hold
down the red button for 30 seconds until the pilot
light remains on when the red button is released.

5.

If the pilot light goes out, repeat step 4. (In a
new range installation this procedure may
have to be repeated several times until air is
purged from gas line.)

6.

Be sure oven door is closed.

7.

T u r n   t h e   o v e n   t h e r m o s t a t   t o   d e s i r e d
temperature setting and turn the oven gas
valve to ON. Oven will light.

8.

Verify that the pilot light is still on.

9.

Turn oven gas valve to OFF.

10. Reinstall the kick plate.

Convection Oven

BEFORE LIGHTING PILOT LIGHT FOR OVEN,
LIGHT ALL PILOTS FOR TOP BURNERS

1.

Remove the oven kick plate.

2.

Turn the master power switch to ON. (the light
between the toggle switches will glow
indicating that the re-igniter is ON.)

3.

Turn the oven gas valve to OFF.

Figure 13: Convection/Standard Oven

Gas Valve Location

4.

Push and hold down the red button on the pilot
valve, the electronic ignition will light the pilot
light. Continue to hold down the red button for
30 seconds until the pilot light remains on
when the red button is released.

5.

Be sure that oven door is closed.

6. Set rocker switch to AUTO.

7. Turn the thermostat to the desired temperature

setting. Turn oven gas valve to ON. The oven
will light and the convection fan will run.

8. Turn the oven gas valve to OFF.

9. Verify that pilot light is still on.

10. Reinstall the oven kick plate.

Summary of Contents for JTRH Series





















Reviews: