background image

150

200

250

300

350

400

450

500

550

L

O

R

O

A

S

T

BA

KI

NG

WARNING

WHEN  MAIN   GAS    TO   THE
APPLIANCE  IS  OFF,  POWER
ON  SWITCH  MUST  BE   OFF.
TURN  OFF   ELECTRIC  &  GAS
TO      APPLIANCE     BEFORE
SERVICING  ALL  CONTROLS.

WARNING

THERMOSTAT

LITE

OFF

POWER

ON

BLOWER

AUTO

P.O.

MANUAL

WHEN  MAIN  GAS  TO  THE
APPLIANCE  IS  OFF,  POWER
ON  SWITCH  MUST  BE  OFF.

O
F
F

Jade Range LLC

A MIDDLEBY COMPANY

2650 Orbiter Street, Brea, CA 92821 • 714-961-2400 • 800-884-5233 • www.jaderange.com

NOTES:

IN LINE WITH ITS POLICY TO CONTINUALLY IMPROVE ITS PRODUCTS, JADE RANGE, LLC RESERVES THE RIGHT TO CHANGE MATERIALS AND SPECIFICATIONS WITHOUT NOTICE.
JADE RANGE EQUIPMENT IS BUILT TO COMPLY WITH APPLICABLE STANDARDS FOR MANUFACTURERS.  INCLUDED AMONG THOSE APPROVAL AGENCIES ARE UL, A.G.A., CSA, ETL  AND OTHERS.

TITAN

     

SERIES

SUPER HEAVY DUTY
RANGE LINE

MODEL SERIES JTRH, JMRH & JTRHE

Installa

Installa

Installa

Installa

Installation &

tion &

tion &

tion &

tion &

Oper

Oper

Oper

Oper

Opera

aa

aation

tion

tion

tion

tion

Manual

Manual

Manual

Manual

Manual

RETAIN THIS MANUAL FOR FUTURE REFERENCE.

Manual number  2413200000 revC      Printed in U.S.A.

Please read this manual completely before attempting to

install or operate this equipment! Notify carrier of damage.

Inspect all components immediately.

Summary of Contents for JTRH Series





















Reviews: