Jacobsen LF550-H-T4F Safety, Operation And Maintenance Manual Download Page 36

Page: 36 / 88

6 CONTROLS

6.7

BACKLAP SWITCH ________________________________________________________

The backlap switch is found on the fan shroud and is used to switch the reels to backlap mode.

For normal operation, the backlap switch must be in the OFF position.

To backlap, press the top of the switch to the ON position. When you backlap, the parking brake
switch must be in the ON position and the traction pedal in the Neutral position. The BACKLAP
MODE screen is shown on the LDU.

6.8

THROTTLE LEVER ________________________________________________________

The throttle lever controls the engine speed. Always operate the mower at
full throttle during normal operation.

4131663

Throttle
Lever

Fast

Slow

Summary of Contents for LF550-H-T4F

























































































Search results

Summary of Contents for LF550-H-T4F

Reviews:

Related manuals for LF550-H-T4F

Brands by name

Popular brands

Jacobsen LF550-H-T4F, Safety, Operation And Maintenance Manual

Search results

Summary of Contents for LF550-H-T4F

Reviews:

Related manuals for LF550-H-T4F

Brands by name

Popular brands