Jacobsen LF550-H-T4F Safety, Operation And Maintenance Manual Download Page 84

Page: 84 / 88

12 QUALITY OF CUT

12.9 RIFLING OR TRAMLINING __________________________________________________

NOTE: Arrow indicates direction of travel.

Rifling or tramlining is a pattern of different cutting heights
that gives the grass an appearance like a wave. This
appearance is normally because of heavy contact points
across a reel and bedknife.

Probable Cause

Remedy

The reel is damaged or is not worn equally.

Check and adjust the HOC on cutting units to same
height.

Loose, missing or over-torqued bedknife screws

Install, replace or tighten the bedknife screws to the
correct torque.

Cut (ground) speed is higher than normal

Reduce the cut (ground) speed.

Summary of Contents for LF550-H-T4F

























































































Search results

Summary of Contents for LF550-H-T4F

Reviews:

Related manuals for LF550-H-T4F

Brands by name

Popular brands

Jacobsen LF550-H-T4F, Safety, Operation And Maintenance Manual

Search results

Summary of Contents for LF550-H-T4F

Reviews:

Related manuals for LF550-H-T4F

Brands by name

Popular brands