Jacobsen LF550-H-T4F Safety, Operation And Maintenance Manual Download Page 28 | Manualshive

Page: 28 / 88

background image

6 CONTROLS

27

6.2.1 IGNITION SWITCH _________________________________________________________

The ignition switch has three positions, OFF, RUN and START. In the RUN
position, the controller program is active and input and output circuits are
monitored.

6.2.2 PARKING BRAKE SWITCH__________________________________________________

To engage the parking brake, press the front of the switch. Parking brake light on LDU (See
6.2.9) will turn on. Operation of the cutting units operation is disabled with the parking brake
engaged.

To disengage parking brake, press the rear part the switch. The parking brake light will turn off.

NOTE: Engine will not start with the parking brake switch in the OFF position.

6.2.3 CRUISE CONTROL SWITCH_________________________________________________

The cruise control switch controls the operation of the cruise control system.

To engage the cruise control, press the traction pedal, push the orange lock forward and press
the front of the switch.

To disengage the cruise control, press the rear part of the cruise control switch, press the rear
part of the parking brake switch or turn the ignition switch to the OFF position.

OFF

RUN

START

«
...
26
27
28
29
30
...
»

Summary of Contents for LF550-H-T4F

























































































Reviews:

No comments

Related manuals for LF550-H-T4F

Brand: McCulloch Pages: 36

MULTICLIP Pro 51 S

Brand: Stiga Pages: 10

Brand: Yard-Man Pages: 44

Brand: Poulan Pro Pages: 30

Brand: ZIPPER MASCHINEN Pages: 65

Brand: Murray Pages: 144

Brand: Sabo Pages: 88

AutoDrive 60-1827-4

Brand: Yard Works Pages: 53

Brand: Improvements Pages: 5

Brand: Black & Decker Pages: 40

Brand: Black & Decker Pages: 17

Brand: Black & Decker Pages: 16

Brand: Black & Decker Pages: 16

Brand: Black & Decker Pages: 24

Brand: Black & Decker Pages: 15

Brand: Black & Decker Pages: 8

Brand: Black & Decker Pages: 6

Brand: Black & Decker Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands