Jacobsen LF550-H-T4F Safety, Operation And Maintenance Manual Download Page 29 | Manualshive

Page: 29 / 88

background image

CONTROLS 6

28

6.2.4 PTO SWITCH _____________________________________________________________

The PTO switch is a 2-position knob type switch to engage and to disengage the cutting units. The
PTO switch must be in the OFF (down) position to start the engine.

Pull on the red knob to move the switch to the ON position. When the PTO switch is in the ON
position, the cutting units are engaged and the joystick is set to automatic mode. When the cutting
units are lowered, the reels will start to turn when forward travel starts. When the cutting units are
lifted or forward movement stops, the reels will stop.

6.2.5 HORN SWITCH ____________________________________________________________

Press the front of the switch to use the horn.

6.2.6 LIGHT SWITCH ____________________________________________________________

The light switch controls the operation of the headlights. Press the front part of the switch to turn on
the headlights. Press the rear part of the switch to turn off the headlights.

«
...
27
28
29
30
31
...
»

Summary of Contents for LF550-H-T4F

























































































Reviews:

No comments

Related manuals for LF550-H-T4F

Brand: Toro Pages: 56

Brand: Snapper Pages: 8

Brand: Roller Derby Pages: 4

Brand: Parker Pages: 25

Brand: Yard-Man Pages: 4

Brand: Toro Pages: 72

Brand: Murray Pages: 144

Harmony II HRR216K1PDA

Brand: Honda Pages: 66

Brand: Toro Pages: 52

Enviromower ENV369B

Brand: Victa Pages: 28

Zero Turn Rotary Mower

Brand: Jacobsen Pages: 62

Brand: Country Home Products Pages: 52

GRA Professional 36V-48

Brand: Bosch Pages: 128

Brand: Bosch Pages: 67

Brand: Bosch Pages: 398

Brand: Bosch Pages: 318

Brand: Bosch Pages: 448

Brand: Craftsman Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands