JR_EYE-02.ENG.MAN.Manual.16.A
- 14 -
5.4 Switching OFF and ON
To switch the EYE-02 camera OFF
, switch it to the
CONFIG
mode (see chapter 3.3). Disconnect the power
and USB cables from the camera and press and hold the power button on the back panel for
3 seconds
.
When the green light on the front panel switches off, the camera shuts down.
To switch the EYE-02 camera ON
, press and hold the power button on the back panel of the camera. Keep
holding the button until the green light on the front panel switches on. The start-up process has started and
you can release the button.
The camera also starts up automatically after it is connected to the AC adaptor or to PC by a USB cable.
Whenever the camera is expected to be switched off for a longer period of time or for transportati-
on, it is strictly recommended to remove the backup battery from the EYE-02 camera.
The camera starts in the same mode it was before switching off with the following exception: In
case you do not have enrolled any remote control and contact (phone number) camera starts in
ENROL mode in place of CONFIG or SLEEP mode. For normal operation there must be minimum 1
remote control and 1 number enrolled in the camera.
5.5 Battery
The EYE-02 camera has an internal backup Li-Ion battery, which allows operating in case of the loss of AC
power. If used in any of the predefined profiles, the backup battery allows the camera to operate for approxi-
mately 24hours. Any individual sensor configuration may shorten this period accordingly.
In case of active MIP sensor, the backup time may be as short as 40 % of the original value. In case of simulta-
neous use of IR illuminator working during AC failure, the backup time may drop to 20 %.
Please, note that each item of network communication will shorten the backup time rapidly, especially if the
camera is operated in a poor network coverage area.
In certain cases, for example when used in locations where AC power isn’t available, it may be desired to
extend the battery operation duration. In such case you may use the special
BAT TERY
mode.
When in the
BAT TERY
mode, the EYE-02 camera reduces dramatically its power consumption in WATCH. It
logs out from the GSM network, switches off the short range radio receiver and switches on the motion-in-
picture detector only after ALERT. It means that the EYE-02 camera, while in the
BAT TERY
mode, can not be
reached by calls or by SMS commands. Additionally, the external detectors and remote controls cannot be
used for the BATTERY mode, too.
The EYE-02 camera keeps all the internal detectors working and reports all events as in the
NORMAL
mode.
After an ALARM, the EYE-02 camera switches on the radio and logs onto the GSM network for 2 minutes. It
reacts to calls, SMS commands and remote controls during these 2 minutes only.
A fully charged battery in the BATTERY mode can operate the EYE-02 camera for up to 30 days.
5.6 Micro SD card
The EYE-02 camera is equipped with an SDmicro memory card slot allowing further extension of the internal
storage capacity. The EYE-02 Camera comes with an inserted 1 or 2GB memory card.
JabloTool DESKTOP software allows you to switch the EYE-02 camera into the USB mode in which you can ac-
cess the SD card as a standard flash disc from an attached PC. To switch to the USB mode, display the device
state screen, switch it into the Advanced user mode, choose CONFIG and USB mode.
Other EYE-02 camera functions are blocked during the PC direct access to the SD card.
When exploring the SD card, you will find the following folder structure:
HISTORY
This folder contains files with complete (all details) log of event history. Files are stored
sequentially in the “ev00001.txt” format.
PICTURE
Archive of static JPEG files recorded at ALARMs (For example:
“p0065401.jpg”
)
VIDEO
Archive of AVI video files recorded during ALARMs (For example:
“vid01021.avi”
)
config.txt
A file with the current configuration of EYE-02 – can be used for backup or restore of
configuration.