ITW GSE 6400 Tier 4 Operation Manual Download Page 52

Page: 52 / 105

Operation Manual – ITW GSE 6400 Tier 4

Update/Save Log (continued) – Menu structure

10:30:00

USB MENU 28/06/2013

Update Display Software

Update Control Card Software

Save Logs

◄

Back

●

Select

Highlight the by using the navigation

◄▼▲►

keys.

Press

●

to select ”USB Menu” sub-menu.

Use the the

▼

▲

to highlight the function

”Update Control Card software”.

Before pressing

●

to select ”Update control card

software”, please remember to insert an USB stick
into the USB port on the control card (located on
the interface board).

Press

●

to select function.

Press

●

to confirm update firmware.

The firmware is now being uploaded to the display
card. Upload % is counting from 0% to 100%. The
system automatically reboots if the update is
successful. Otherwise, an Update has failed!
Message is displayed.

10:30:00

USB MENU 28/06/2013

Updating Control Card

10:30:00

USB MENU 28/06/2013

USB Firmware Update Detected

Do you wish to update?

0.0%

Press

●

to update firmware

10:30:00

USB MENU 28/06/2013

Updating Control Card

Update Succesful! Please Reboot!

USB connection

Control card

OM2248 Rev B

Page 51 of 104

Summary of Contents for 6400 Tier 4










































































































Search results

Summary of Contents for 6400 Tier 4

Reviews:

Related manuals for 6400 Tier 4

Brands by name

Popular brands

ITW GSE 6400 Tier 4, Operation Manual

Search results

Summary of Contents for 6400 Tier 4

Reviews:

Related manuals for 6400 Tier 4

Brands by name

Popular brands