ITW GSE 6400 Tier 4 Operation Manual Download Page 43

Page: 43 / 105

Operation Manual – ITW GSE 6400 Tier 4

11:27:47

Setup Menu

28/06/2013

Language

◄

Back

●

Select Parameter.

Settings:

English, French, German,
Italian, Polish, Portuguese, etc.

Refer to Section 3 – 4.19

11:27:47

Setup Menu

28/06/2013

Language

English

◄

Back

●

Modify

Use the the

▼

▲

to browse through the

various set-up lines / parameters. The
selectable line will be highlighed in
green.

Press

●

to select the parameter you

want to change.

Press

●

to Modify parameter.

Parameter will now be highlighted in
green.

Use the the

▼

▲

to adjust parameter.

Press

●

to save changes.

Use

◄

to leave the sub-menu and

return to basic Icon Menu.

Notice!
Availability of parameters may vary
depending on the mode of the unit
Standby / Engine Running etc.

Setup (continued) – Menu structure

OM2248 Rev B

Page 42 of 104

Summary of Contents for 6400 Tier 4










































































































Search results

Summary of Contents for 6400 Tier 4

Reviews:

Related manuals for 6400 Tier 4

Brands by name

Popular brands

ITW GSE 6400 Tier 4, Operation Manual

Search results

Summary of Contents for 6400 Tier 4

Reviews:

Related manuals for 6400 Tier 4

Brands by name

Popular brands