ITT Goulds Pumps VCW Installation, Operation And Maintenance Manual Download Page 20

Page: 20 / 71

4.2.2 Concrete foundation requirements

Requirements

Make sure that you meet these requirements when you prepare the pump foundation:

•

The foundation must be able to absorb any vibration.

•

The foundation must be able to form a permanent and rigid support for the pumping unit.

•

The foundation must be of adequate strength in order to support the complete weight of the pump
and driver, plus the weight of the liquid that passes through it.

Typical installation

A typical installation has these characteristics:

•

Bolts with a pipe sleeve that is two and a half times the size of the bolt diameter embedded in the
concrete

•

Properly sized

•

Located in accordance with the dimensions given in the example drawing

•

Enough space inside the pipe sleeves to allow the final position of the foundation bolts to align with
the holes in the sub-base flange

Barrel flange, sub-base or discharge head

Foundation

Sleeve

Dam

Grout

Anchor bolt

Figure 5: Example of a typical installation

4.2 Pre-installation

Model VCW Installation, Operation, and Maintenance

Summary of Contents for Goulds Pumps VCW








































































Search results

Summary of Contents for Goulds Pumps VCW

Reviews:

Related manuals for Goulds Pumps VCW

Brands by name

Popular brands

ITT Goulds Pumps VCW, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps VCW

Reviews:

Related manuals for Goulds Pumps VCW

Brands by name

Popular brands