ITT Goulds Pumps VCW Installation, Operation And Maintenance Manual Download Page 16 | Manualshive

Page: 16 / 71

background image

3 Product Description

3.1 General description

The Model VCW pump is vertical, industrial, turbine-type pump designed to meet a wide variety of appli-
cations.

This pump has these capabilities:

•

Capacities up to 90850 m3/h | 400,000 gpm

•

Heads up to 183 m | 600 ft.

•

Power up to 7,457 kW | 10,000 hp

Bowl assembly

The bowl construction is flanged for accurate alignment and ease of assembly and disassembly. Impel-
lers are either open or enclosed, depending on the design requirements. Impellers are keyed to the
shaft.

Column

Flanged column construction with rabbeted fits provides positive shaft and bearing alignment, and also
eases assembly and disassembly. The line shaft is supported within the column with the use of bearing
retainers that are spaced in order to provide vibration-free operation and ensure long bearing and shaft
wear.

Discharge head

The discharge head is designed to support the pump and to align the driver to the pump. Driver support
windows provide access to packing or seal piping and allow for easy adjustment of seals and couplings.
In the case of an underground discharge, these features are part of a separate motor stand above
ground.

Suction barrel (can)

The suction barrel flange, or separate mounting flange, is designed to support the weight of the pump
and driver when it is full of liquid. You can install the suction barrel in a sleeve or open steel structure with
thermal insulation around the suction barrel below its mounting flange.

Thrust pot

A thrust pot is an option that is used when the driver is not designed to carry the axial pump thrust.

Drivers

Solid shaft drivers are used with most industrial applications. The rigidity of the rotor enhances vibration-
free operation when mechanical seals are used.

3.2 Nameplate information

Important information for ordering

Every unit has a nameplate that provides information about it.

When you order spare parts, identify this pump information:

•

Model

3 Product Description

14

Model VCW Installation, Operation, and Maintenance

«
...
14
15
16
17
18
...
»

Summary of Contents for Goulds Pumps VCW








































































Reviews:

No comments

Related manuals for Goulds Pumps VCW

Brand: SAER Elettropompe Pages: 76

Brand: Kospel Pages: 40

Johnson Pump CombiProLine OH3

Brand: SPX FLOW Pages: 67

Brand: Zenith Pages: 12

Brand: IceManCooler Pages: 2

ecoTOUGH NRC111-DV-LP

Brand: Noritz Pages: 32

BC-F20HWR2-200L

Brand: enertik Pages: 33

Brand: Vagner Pool Pages: 35

Brand: Watts Pages: 22

Brand: Graco Pages: 32

Brand: Q-Pumps Pages: 44

Brand: B. Braun Pages: 86

Brand: Jandy Pages: 96

Brand: Calorex Pages: 44

Brand: Binks Pages: 40

MONOLITE 320 GT

Brand: ICI Caldaie Pages: 36

Brand: Desmi Pages: 34

Brand: Flotec Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands