ITT Goulds Pumps VCW Installation, Operation And Maintenance Manual Download Page 10 | Manualshive

Page: 10 / 71

background image

•

All work on the product must be carried out by certified electricians and ITT-authorized

mechanics. Special rules apply to installations in explosive atmospheres.

•

All users must know about the risks of electric current and the chemical and physical

characteristics of the gas and/or vapor present in hazardous areas.

•

Any maintenance for Ex-approved products must conform to international and national

standards.

Product and product handling requirements

These are the product and product handling requirements for Ex-approved products in potentially explo-
sive atmospheres:

•

Only use the product in accordance with the approved motor data stated on the nameplates.

•

The Ex-approved product must never run dry during normal operation. Dry running during service
and inspection is only permitted outside the classified area.

•

Never start a pump with a closed suction valve or blocked suction line.

•

Before you start working with the product, make sure that the product and the control panel are iso-
lated from the power supply and the control circuit, so they cannot be energized.

•

Do not open the product while it is energized or in an explosive gas atmosphere.

•

Make sure that thermal contacts are connected to a protection circuit according to the approval
classification of the product.

•

Intrinsically safe circuits are normally required for the automatic level-control system by the level
regulator if mounted in zone 0.

•

The yield stress of fasteners must be in accordance with the approval drawing and the product
specification.

•

Make sure that the equipment is properly maintained:

•

Monitor the pump components and the end temperature of the liquid.

•

Maintain proper bearing lubrication.

•

Do not modify the equipment without approval from an authorized ITT representative.

•

Only use parts that have been provided by an authorized ITT representative.

1.1 Safety

8

Model VCW Installation, Operation, and Maintenance

«
...
8
9
10
11
12
...
»

Summary of Contents for Goulds Pumps VCW








































































Reviews:

No comments

Related manuals for Goulds Pumps VCW

Brand: Nelson Pages: 12

Brand: A.O. Smith Pages: 2

Brand: DAB Pages: 13

Brand: Davey Pages: 12

Brand: Barmesa Pumps Pages: 42

Brand: Danfoss Pages: 38

Brand: EBARA Pages: 40

Brand: EBARA Pages: 534

Brand: EBARA Pages: 60

Brand: ebm-papst Pages: 8

Brand: salmson Pages: 49

Clima Canal JDPC.002

Brand: Jaga Pages: 8

Brand: PAPILLON Pages: 22

Brand: BLACKMER Pages: 24

Feeder/Deliming System EV9797-20

Brand: Everpure Pages: 2

Brand: Warren rupp Pages: 22

INSTANT-FLOW MICRO MIX Series

Brand: Chronomite Pages: 2

Brand: IBAIONDO Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands