ITT Goulds Pumps VCW Installation, Operation And Maintenance Manual Download Page 14

Page: 14 / 71

Pump type

Lifting method

A disassembled pump

Use suitable lifting devices attached to the component lifting lugs or suitable swivel
hoist rings through the component flanges.

Examples

Figure 2: VCW lifted from horizontal to vertical (for pumps up to 15 feet (4.6 meters) in length))

NOTICE:

Actual number of lifting points may vary for specific pump design and installation circumstan-
ces. Refer to order-specific drawings for details.

2.4 Pump storage requirements

Requirements

Vertical pumps require proper preparation for storage and regular maintenance during storage. The
pump is considered in storage when it has been delivered to the job site and is awaiting installation.

For specific requirements for storing motors, gearboxes, engines, panels, sealing plans and other auxilia-
ries, contact the equipment manufacturer.

Storage preparation

Condition

Proper preparation

Indoor storage area (preferred)

•

Pave the area.

•

Clean the area.

•

Drain the area and keep it free from flooding.

Outdoor storage area (when indoor
storage is not available)

•

Observe all indoor storage requirements.

•

Use weather-proof coverings such as flame-resistant sheeting or
tarpaulins.

•

Place coverings in a manner that maximizes drainage and air circu-
lation.

•

Place moisture absorbing material in the quantity to prevent con-
densation

•

Tie coverings down in order to protect the pump from wind damage.

Placement of pumps and compo-
nent parts

•

Place the unit on skids, pallets, or shoring higher than 15 cm | 6 in.
from the ground for good air circulation.

•

Sort the parts in order to permit easy access for inspection and/or
maintenance without excessive handling.

2.4 Pump storage requirements

Model VCW Installation, Operation, and Maintenance

Summary of Contents for Goulds Pumps VCW








































































Search results

Summary of Contents for Goulds Pumps VCW

Reviews:

Related manuals for Goulds Pumps VCW

Brands by name

Popular brands

ITT Goulds Pumps VCW, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps VCW

Reviews:

Related manuals for Goulds Pumps VCW

Brands by name

Popular brands