ITT Flygt 3102 Service And Repair Instructions Download Page 25

Page: 25 / 72

Torque,

Nm (ft-

lbs)

8.8

2.9 (2.1) 5.7 (4.2) 9.8 (7.2) 24 (18)

47 (35)

81(60)

194 (143) 385 (285) 665 (490) 1310

(966)

10.9

4.0 (2.9) 8.1 (6)

14 (10.3) 33 (24.3) 65 (48)

114 (84) 277 (204) 541 (399) 935 (689) 1840

(1357)

12.9

4.9 (3.6) 9.7 (7.2) 17 (12.5) 40 (30)

79 (58)

136 (100) 333 (245) 649 (480) 1120

(825)

2210

(1630)

Screws with countersunk heads

Stainless steel, A2 and A4

Property

class

M10

M12

M16

M20

M24

Torque,

Nm (ft-lbs)

70 +80

1.2 (0.9)

2.7 (2)

5.4 (4)

9.3 (6.9)

22 (16)

44 (32)

76 (56)

120 (88)

187 (138)

Carbon steel and alloyed steel
Torque,

Nm (ft-lbs)

8.8

2.3 (1.7)

4.6 (3.4)

7.8 (5.8)

19 (14)

38 (28)

65 (48)

158 (116) 308 (228) 532 (392)

10.9

3.2 (2.4)

6.5 (4.8)

11(8)

26 (19)

52 (38)

91 (67)

222 (164) 433 (320) 748 (552)

12.9

3.9 (2.9)

7.8 (5.8)

14 (10.3)

32 (23.6)

63 (46)

109 (80)

266 (196) 519 (383) 896 (661)

Change the oil

This image shows the plugs that are used to change the oil.

Oil plug

Empty the oil

WARNING:
The oil housing may be pressurized. Hold a rag over the oil plug to prevent oil from spraying out.

1. Place the pump in a horizontal position and unscrew the oil plug.

If the pump has a hole with the markings "oil out" it is important that this hole is used for drainage.

Maintenance (Continued)

Flygt 3102 Service and Repair Instructions

Summary of Contents for Flygt 3102









































































Search results

Summary of Contents for Flygt 3102

Reviews:

Related manuals for Flygt 3102

Brands by name

Popular brands

ITT Flygt 3102, Service And Repair Instructions

Search results

Summary of Contents for Flygt 3102

Reviews:

Related manuals for Flygt 3102

Brands by name

Popular brands