background image

Section 1, Overview  

1-6  

POLAR

HD Heating Module 

 

1.5  Equipment, Tools and Skills 

As the user and/or installer, you must be qualified and authorized to 
do the installation, which requires mechanical aptitude and electrical 

knowledge.  Make sure you comply with existing industry practices, 
using the highest and most recent standards and codes.  Good 
workmanship is essential.  Please refer back to Section 1  – 
Overview, sub-Section 1.2, Protect Your Warranty

You will need the following equipment and tools to install the 
heating system (not supplied).  This list does not include optional 

equipment and accessories: 

 

Standard tools normally available in a well-equipped shop. 

 

Approved fasteners for mounting the heater unit. 

 

Steel (or stainless steel) 2” ID exhaust system piping, maximum 
12’ with no bends. (See Section 3 – Installing the Exhaust 

System, for details when bends are present.). 

 

Exhaust collar. 

 

ITR-muffler with straight-through design. 

 

1/4” supply fuel line, approved rubber or copper. 

 

#10 sheet metal screws or wood screws to mount fan units 

inside the occupied areas. 

 

Heater hose (to connect the Distribution Module (optional) hose 
fittings to interior fans). 

 

Overflow  tank  to  connect  to  the  POLAR™  HD  Heating    Module 
with clear plastic 3/8” hose; tank must be heavy-duty plastic, 
with a screw-down cap, and sturdy enough to mount firmly to a 

vertical surface. 

 

Up to five (5) thermostats (DC compatible) to allow temperature 
regulation of the heating zones when connected to the 
Distribution Module. 

Summary of Contents for POLAR HD

















































































Reviews: