ITR POLAR HD Installation And Operating Manual Download Page 4

Page: 4 / 80

Table of Contents

Installation and Operating Manual for POLAR

™

HD Heating Module

5.2

Fan System Operation ................................... 5-2

Features ....................................................... 5-2

Multiple Zone Heating ..................................... 5-3
Accessories and Components Needed ................ 5-3

5.3

What NOT to Do ........................................... 5-4

5.4 Mounting

Locations

.......................................

5-4

5.5 Procedure

....................................................

5-5

Section 6, Wiring the Electrical System ..................... 6-1

6.1

Before You Begin .......................................... 6-1

6.2 12

VDC

.......................................................

6-1

6.3 120

VAC

...................................................... 6-2

6.4

Remote Operating Panel Cable ........................ 6-2

6.5

Main Electronic Control Board ......................... 6-3

6.6

Distribution Module Zone Control Board

(Optional)

.................................................... 6-3

6.7

What NOT to Do ........................................... 6-4

Section 7, Plumbing the System ................................ 7-1

7.1

Before You Begin .......................................... 7-1

7.2 Plumbing

Installation

..................................... 7-1

7.3

What NOT to Do ........................................... 7-4

7.4 Installation

Procedure

...................................

7-4

Section 8, Operating the POLAR

™

HD Heating Module 8-1

8.1

Features of your POLAR

™

HD Heating Module ..... 8-1

8.2

Your Heating Module Model ............................ 8-2

8.3

Operating Instructions for the

POLAR

™

HD Heating Module ............................ 8-3

8.4

Turning the Power to the

POLAR

™

HD Heating Module ON ....................... 8-4

8.5

Activating the Burner (Primary)

and AC Heat (Secondary) from the

Remote

Operating

Panel

................................

8-5

8.6

Activating the Cabin Fan Heaters

through

the

Thermostats

...............................

8-6

8.7

Activating the Domestic Hot Water .................. 8-6

8.8

Activating the Engine Heat ............................. 8-6

8.9

Functions of the Remote Operating Panel ......... 8-7

8.10

Functions of the Heating Module Control Panel .. 8-9

Summary of Contents for POLAR HD

















































































Search results

Summary of Contents for POLAR HD

Reviews:

Related manuals for POLAR HD

Brands by name

Popular brands

ITR POLAR HD, Installation And Operating Manual

Search results

Summary of Contents for POLAR HD

Reviews:

Related manuals for POLAR HD

Brands by name

Popular brands