manualshive.com logo in svg

ITech IT8600 Series, Programming Manual

Share
Download
ITech IT8600 Series Programming Manual Download Page 23

 

 

Measurement Commands 

 

Copyright © Itech Electronic Co., Ltd.

 

12 

MEASure:POWer? 

FETCh:POWer? 

This command is used to read the active power of WATT as the unit. 

Command syntax: 

MEASure[:SCALar]:POWer[:ACTive]? 

FETCh[:SCALar]:POWer[:ACTive]? 

Returned value: 

<NR3>

 

MEASure:POWer:MAXimum? 

FETCh:POWer:MAXimum? 

This command is used to read the maximum input power value. 

Command syntax: 

MEASure[:SCALar]:POWer[:AMPLitude]:MAXimum? 
FETCh[:SCALar]:POWer[:AMPLitude]:MAXimum? 

Returned value:

 

<NR3> 

MEASure:POWer:APParent? 

FETCh:POWer:APParent? 

This command is used to read the apparent power of VA as the unit. 

Command syntax: 

MEASure[:SCALar]:POWer:APParent? 

FETCh[:SCALar]:POWer:APParent? 

Returned value:

 

<NR3> 

          ООО "Техэнком"     Контрольно-измерительные приборы и оборудование     www.tehencom.com          

Summary of Contents for IT8600 Series














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands