manualshive.com logo in svg

ITech IT8600 Series, Programming Manual, Page: 19 / 77

Share
Download
ITech IT8600 Series Programming Manual Download Page 19

 

 

Remote Control 

 

Copyright © Itech Electronic Co., Ltd.

 

8 

  The device is RL1 capable. 

  The device is DT1 capable. 

1.6.2 GPIB Interface 

First connect GPIB port of load to GPIB card of PC with IEEE488 BUS. They 

must be sufficient contact and tighten the screws. And then set address. The 

address can be set from 0 to 30. Press 

[Menu]

 key to enter system menu, 

press 

[COMM CONFIG]

 to find Communication interface. Select GPIB, and 

then set the GPIB address, press 

[Enter]

 to confirm. The electronic load 

operates from a GPIB address set from the front panel. The GPIB address is 

stored in non-volatile memory. 

1.6.3 LAN Interface 

Press 

[Menu]

 on the front panel together to access the menu. Select 

[COMM 

CONFIG]

 to enter communication configuration page. Select LAN by pressing 

arrow keys and then configure Gateway, IP, Mask and Socket Port in the LAN 

option. Use a cross network cable through LAN interface to connect PC. 

 

          ООО "Техэнком"     Контрольно-измерительные приборы и оборудование     www.tehencom.com          

Summary of Contents for IT8600 Series














































































Reviews:

No comments