manualshive.com logo in svg

ITech IT8600 Series, Programming Manual

Share
Download
ITech IT8600 Series Programming Manual Download Page 22

 

 

Measurement Commands 

 

Copyright © Itech Electronic Co., Ltd.

 

11 

MEASure:CURRent:MINPeak? 

FETCh:CURRent:MINPeak? 

This command is used to read the negative peak current of electronic load. 

Command syntax: 

MEASure[SCALar:]CURRent:MINPeak? 

FETCh:[SCALar:]CURRent:MINPeak? 

Returned value: 

<NR3> 

MEASure:CURRent:MAXPeak? 

FETCh:CURRent:MAXPeak? 

This command is used to read the positive peak current of electronic load. 

Command syntax: 

MEASure[:SCALar]:CURRent:MAXPeak? 

FETCh[:SCALar]:CURRent:MAXPeak? 

Returned value: 

<NR3>

 

MEASure:FREQuency? 

FETCh:FREQuency? 

This command is used to read the frequency of Hertz as the unit. 

Command syntax: 

MEASure[:SCALar]:FREQuency? 

FETCh[:SCALar]:FREQuency? 

Returned value: 

<NR3> 

          ООО "Техэнком"     Контрольно-измерительные приборы и оборудование     www.tehencom.com          

Summary of Contents for IT8600 Series














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands