background image

 

 

 

  Dry Filter Spraybooth Installation and Maintenance Instructions

 

 

 

 

 

 

 
 

 

 
In order to comply with the requirements of CE marking, all Spraybooths must now be fitted with a facility for an 
emergency stop within easy reach of the operator.  

Airflow

  will be pleased to quote for the supply of a suitable 

emergency stop wire kit, now available to meet the requirements of this regulation.  Please contact our Sales 
Department for further information. 
 

13   

Fitting of Filters

 

 

Airflow

 Dry Filter Spraybooths are fitted with either Paper-Type Filter Medium or Open-Weave Filter Medium.  Please 

identify which type of Filter Medium has been supplied with your Spraybooth and follow the appropriate instruction 
paragraph below. 
 
If you are unsure as to which type of filter has been supplied, please check one of the filter support frames.  If the frame 
is fitted with a 50mm by 50mm weldmesh panel then your Spraybooth is to be used with Open-Weave Type Filter 
Medium.  If the apertures are open, without the weldmesh panel, then this Spraybooth can only be used with the 
concertina Paper-Type Filter Medium. 
 
FITTING PAPER-TYPE FILTER 
Remove the filter paper from the box. First begin by stretching out the filter paper on the floor to the correct pleats per 
metre.  Measure the width of filter paper appropriate to the width of your Spraybooth and add to this length an extra 
250mm.  Cut the paper this length.  At the left and right hand side of each filter paper slot is an angled filter paper clip.  
Gather together the first three or four corrugations at the left-hand side of the filter paper and insert them into the filter 
paper clip.  This will now hold the left-hand side of the filter paper.  Stretch the filter paper carefully across the width of 
the Booth until you reach the right hand side.  Now gather together the remaining corrugations and insert into the right 
hand paper clip.  Repeat this operation for the lower filter paper slot and the installation of the filter medium is now 
complete. 
 
FITTING OPEN-WEAVE FILTER MEDIUM 
Open-Weave Filter Medium is supplied on a roll and must be fitted into the Spraybooth with the green surface facing 
towards the operator.  Unroll a suitable length of filter medium on the floor and cut to width of the Spraybooth.  At the 
left and right hand side of the Spraybooth filter slot is a filter medium clamp plate secured to the Spraybooth with self-
tapping screws.  Remove both filter clips and stretch the filter medium across the face of the Spraybooth slot.  Once in 
position, replace the two filter medium clips by screwing the self-tapping screws through the Filter Medium.  Repeat 
this operation for the lower filter medium slot and the installation of the Spraybooth filter is now complete. 

 

14   

Commissioning

 

 
Commissioning of 

Airflow

 Dry Filter Spraybooths is a simple operation. 

 

Summary of Contents for DEC2.2















Reviews: