iPulse iPB4 User Manual Download Page 24 | Manualshive

Page: 24 / 42

background image

iPB4 Biometric Device Range

–

Installation & User Guide

–

Rev 07 ©2017-2018 iPulse Systems

23

SECTION 8

IQSUITE AND OTHER SOFTWARE

The configuration and use of your iPBx Biometric Device is dependent on the type of software you are
using. All iPBx devices are compatible with the iPulse

IQ

Suite.cloud

software system, both in the hosted or

local environments, and are configured to work out of the box in what is known as a

zero-configuration

mode (ZCM)

. ZCM is currently only available when using the iPBx through the

IQ

Suite.cloud

platform.

When using your iPBx biometric device with

IQ

Suite.cloud

, you will not need to do anything other than to

ensure that the iPBx is connecte

d (via the IntelliRelay™) to

the local network, is able to receive an IP address

and gateway from the local DHCP server and is able to access the internet.

Thereafter, you may follow the

IQ

Suite.cloud

manual for further details of how to connect the device to

the software and configure it from there.

However, there are many other software solutions available, including the following:

•

IQ

Suite

4.4x (iPulse Systems)

•

XTime (G4S Secure Solutions)

•

Smart Time (Page Automation)

•

Jarrison Time (Jarrison Systems)

•

iCPAM (Identiv)

For more information on how to configure your device with each of these platforms, or with

IQ

Suite.cloud

platform, please visit

http://www.iqsuite.cloud

and download the relevant manual. You will also find a

wealth of updated information on which software systems support the iPBx out of the box, and how to use
or configure your iPBx to work with these solutions.

«
...
22
23
24
25
26
...
»

Summary of Contents for iPB4











































Reviews:

No comments

Related manuals for iPB4

Brand: S&C Pages: 40

Brand: LAE electronic Pages: 7

Brand: LAE electronic Pages: 2

Brand: Vageo Pages: 2

Brand: Vacon Pages: 6

Brand: Vacon Pages: 24

Brand: Vacon Pages: 30

Brand: Vacon Pages: 81

Brand: Vacon Pages: 100

Brand: Eaton Pages: 96

Brand: V2 Pages: 12

Brand: H3C Pages: 5

Brand: z21 Pages: 2

Brand: TEL Pages: 26

Brand: Vimar Pages: 32

Brand: Rain Bird Pages: 18

Brand: IFM Pages: 41

SMARC conga-SMX8-X

Brand: Congatec Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands