iPulse iPB4 User Manual Download Page 20 | Manualshive

Page: 20 / 42

background image

iPB4 Biometric Device Range

–

Installation & User Guide

–

Rev 07 ©2017-2018 iPulse Systems

19

SECTION 6

INSTALLATION GUIDELINES

Your iPB4 biometric device is rated as an IP52 unit. For more information on what this means, please see
Appendix A

–

Understanding IP Ratings.

A conversion kit is available that allows you to increase the IP rating of device. For more information, please
ask your supplier or visit www.ipulsesystems.com.

This rating also depends on the quality of installation. For best results it is recommended that the iPB4
biometric device be mounted indoors or at least under a covered area, and that it should not be installed
in an area where it is exposed to the elements.

An iPB4 was designed to be exceptionally easy to install and maintain. Looking at Figure 9 - iPB4 Installation
Diagram above, you can see that the back plate should be mounted to the wall, with a single screw
connecting the front part of the device to the back plate.

Figure 9 - iPB4 Installation Diagram

«
...
18
19
20
21
22
...
»

Summary of Contents for iPB4











































Reviews:

No comments

Related manuals for iPB4

Leroy-Somer R180

Brand: Nidec Pages: 20

Brand: UniKey Pages: 20

Brand: Hable Pages: 3

Max Charge MC-624

Brand: Balmar Pages: 8

MAX CHARGE MC-614

Brand: Balmar Pages: 20

Brand: Taie Pages: 28

ROBO Cylinder RCP2 Series

Brand: IAI Pages: 5

SIGMA CONTROL 2

Brand: KAESER KOMPRESSOREN Pages: 246

Brand: Vageo Pages: 2

Brand: ISVT Pages: 78

Brand: Linear Technology Pages: 8

SYSVRF AHU 10HP S

Brand: SystemAir Pages: 16

Brand: Zapi Pages: 30

Brand: Phoenix Contact Pages: 56

Brand: ADLINK Technology Pages: 37

Brand: Variotech Pages: 24

Brand: Patton Pages: 56

Brand: WAGO Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands