24
25
C L E A N I N G A N D M A I N T E N A N C E
C L E A N I N G A N D M A I N T E N A N C E
Ventilation system iV-Smart+ / sMove controller
•
Operating instructions
Ventilation system iV-Smart+ / sMove controller
•
Operating instructions
x
Z
Cleaning and reassembling the thermal accumulator insert
Soft brush, lint-free soft cloth and warm water
Requirements:
The thermal accumulator insert has been removed.
Ź
Place inVENTron on an even surface.
Ź
Remove the Slim guiding vane from the fan.
Step 1: Carefully bend the lateral strips on the
guiding vane away from the fan one after the
other.
Hold
WKH¿UVWUHPRYHGVWULSLQWKHFXUUHQWSRVLWLRQ
with one hand until the guiding vane is completely
removed.
Ö
The guiding vane is separated from the fan
Step 2: Lift the guiding vane upwards.
2
1
z{ |
/
} ~
:
Incorrect cleaning of the ther-
mal accumulator
will result in damage to the
insulation on the thermal accumulator.
• Always clean the thermal accumulator
under warm running water.
Never clean it in the dishwasher.
Ź
Clean the thermal accumulator under warm
running water.
Ź
Let the thermal accumulator drip dry.
Ź
Wait until the thermal accumulator is completely
dry.
Ö
You have removed the thermal accumulator
insert.
z{ |
/
} ~
:
When breaking the attachment
strips on the guiding vane,
the guiding vane
can no longer be attached to the fan!
• Carefully bend the strips away from the
guiding vane.
• If you can feel resistance, stop bending the
strips outwards.
2
1
Ź
Turn the fan so that the remaining guiding vane is
pointing upwards.
Ź
Remove the guiding vanes from the fan.
Ö
Remove the remaining guiding vane as previ-
ously described.
1
2
3
Ź
Reattach the guiding vanes to the reversible fan.
Ensure
that the smaller Slim guiding vane is
located on the side
WITHOUT
type plate.
Ö
Slim
Standard
Ź
Step 1: Clean both parts of the guiding vane care-
IXOO\ZLWKDVRIWEUXVKRUXQGHUZDUPÀRZLQJZDWHU
Ź
Let the guiding vane drip dry. Wait until the guiding
vane is completely dry.
Ź
Step 2: Clean the reversible fan carefully with a
soft brush.
1
2
Ö
You have removed the thermal accumulator insert.
Ź
Connect the wired plug to the BUS connector.
Make sure
that the markings on the plug and
socket are aligned.
,IWKHUHDUHQRPDUNLQJVRQWKHFRQQHFWRUVWDUWRQH
RIWKHSDLUHGIDQVLQH[WUDFWDLUPRGHDQGWKHRWKHU
LQVXSSO\DLUPRGH
(
Appendix 1: Wiring protocol or
26)
Ź
Step 1: From the interior, slide the thermal accu-
mulator into the wall sleeve as far as the end stop
tape.
Make sure
that the handle is facing towards the
interior.
Ź
Step 2: Insert inVENTron into the wall sleeve so
that you can reach both cables.
Ensure
that the smaller Slim guiding vane is
facing towards the interior.
Slim
Standard
1
2
Ź
Slide inVENTron as far as the thermal accumulator.
Ö
You have cleaned and re-installed the thermal
accumulator insert.
2 x
4
5
6
7
