x
&OHDQLQJUHSODFLQJGXVW¿OWHUV
TIP:
inVENTer
GXVW¿OWHUVRIFODVV*DUHKLJKO\GXUDEOHDQGFDQEHZDVKHGUHSHDWHGO\:H
UHFRPPHQGFOHDQLQJWKHGXVW¿OWHUUHJXODUO\
)RUVSHFL¿FUHTXLUHPHQWVSROOHQ¿OWHUPLFUR¿OWHUDQGDFWLYDWHGFDUERQ¿OWHUDUHDYDLODEOHDV
DFFHVVRULHV<RXFDQ¿QGDVVHPEO\LQVWUXFWLRQVLQWKH¿OWHURSHUDWLQJLQVWUXFWLRQVSURYLGHG
Requirements:
7KHUHYHUVLEOHIDQLVVZLWFKHGRႇRQWKHFRQWUROOHU
The inner cover's panel has been removed. (
3.1)
5.3
Removing the thermal accumulator insert
Pen to mark the connector orientation
Requirements:
7KHUHYHUVLEOHIDQLVVZLWFKHGRႇRQWKHFRQWUROOHU
7KHGXVW¿OWHUKDVEHHQUHPRYHG
5.2)
TIP:
Before removing, mark the orientation of the green controller plug. This will prevent the
reversible fan spinning in the wrong direction after reassembly.
22
23
C L E A N I N G A N D M A I N T E N A N C E
C L E A N I N G A N D M A I N T E N A N C E
Ventilation system iV-Smart+ / sMove controller
•
Operating instructions
Ventilation system iV-Smart+ / sMove controller
•
Operating instructions
Ź
3XOOWKHFRQWDPLQDWHG¿OWHURXWRIWKHLQQHUFRYHU
base plate by the tab.
Ö
7KHGXVW¿OWHUKDVEHHQUHPRYHG
Ź
Insert a new
or
FOHDQHGGXVW¿OWHULQWRWKHEDVH
plate.
Ensure
\RXSXVKWKH¿OWHUULQJ¿UPO\EHWZHHQWKH
¿[LQJSURMHFWLRQVDQGWKHLQQHUHGJHRIWKHLQQHU
cover base plate.
Ensure
WKDWWKHWDERQWKH¿OWHUULQJLVSRLQWLQJ
towards the interior.
Ź
Place the cover on the four spacers.
Ensure
that the inVENTer logo is located on the
bottom right).
Ź
Press the side detent lugs inwards on the inner
cover base plate's spacers.
Ź
Slide the inner cover panel onto the spacers.
Ö
All spacers noticeably snap in.
Ö
<RXKDYHFKDQJHGWKHGXVW¿OWHU
Ź
&OHDQWKHGXVW¿OWHUXQGHUZDUPUXQQLQJZDWHU
Ź
:DLWXQWLOWKH¿OWHULVFRPSOHWHO\GU\
or
Ź
'LVSRVHRIWKHGXVW¿OWHULIGHIHFWLYH
Ź
Step 1: Remove inVENTron from the wall sleeve
by the knob.
Ź
Step 2: Remove the thermal accumulator from the
wall sleeve by the handle.
Ź
Mark the orientation of the BUS connector. This
will prevent the reversible fan spinning in the
wrong direction after reassembly.
Ź
Disconnect the BUS connector.
n
-
p
& y
: In case of damage to the ce-
ramic thermal accumulator
it will no longer
function!
• Do not throw the ceramic thermal accu-
mulator.
• Store the thermal accumulator in the
standing position outside the wall sleeve.
Ö
You have removed the thermal accumulator insert.
1
2
CLICK
1
2
3
4
1
2
