manualshive.com logo in svg

Invacare Top End Excelerator XLT, Owner'S Operator And Maintenance Manual, Page: 60 / 64

Share
Download
Invacare Top End Excelerator XLT Owner'S Operator And Maintenance Manual Download Page 60

Excelerator™ XLT Series

60

Part No. 1114850

Removing the Front Wheel (FIGURE 15).

1. Open the quick-release lever securing the front wheel to the fork (DETAIL "A" of

FIGURE 15).

2. Loosen the knob on the opposite side of the quick-release lever.
3. Remove the wheel from the fork.
4. Remove the chain from the front wheel.

Installing the Front Wheel (FIGURE 15).

1. Place the chain over the front wheel sprocket.
2. Position the chain into the fork.
3. Tighten the knob on the opposite side of the quick-release lever.
4. Secure the wheel to the fork with the quick-release lever.

DETAIL "A" -

FRONT WHEEL

QUICK-RELEASE

LEVER

Quick-release

Lever

NOTE: Quick Release Lever

is on opposite side of wheel.

Chain

Front Wheel

Fork

Sprocket

FIGURE 15 - REMOVING/INSTALLING THE FRONT WHEEL

SECTION 8

OPTIONS

OPTIONS

All manuals and user guides at all-guides.com

Summary of Contents for Top End Excelerator XLT

































































Reviews:

No comments