manualshive.com logo in svg

Invacare Top End Excelerator XLT, Owner'S Operator And Maintenance Manual, Page: 58 / 64

Share
Download
Invacare Top End Excelerator XLT Owner'S Operator And Maintenance Manual Download Page 58

Excelerator™ XLT Series

58

Part No. 1114850

USING THE TRAVEL READY OPTION

NOTE: This procedure is for Excelerator XLT Pro and Gold models only.

The travel ready option allows the handcycle to be quickly and easily disassembled for

travel.

NOTE: Reverse the steps below to reassemble the handcycle.

1. Remove the rear wheels. Refer to INSTALLING/ADJUSTING THE REAR WHEEL

AND QUICK-RELEASE AXLES in SECTION 6 of this manual.

2. Remove the camber bar. Refer to REMOVING/INSTALLING THE CAMBER BAR in

this procedure.

3. Remove the footrests. Refer to SECTION 5 of this manual.
4. Remove the fork and front wheel. Refer to REMOVING/INSTALLING THE FORK

AND FRONT WHEEL in this procedure.

REMOVING/INSTALLING THE CAMBER BAR (FIGURE 13)

NOTE: To install the camber bar, reverse the steps below.

1. ADJUSTABLE ANGLE SEATS ONLY - Loosen, but do not remove the two (2) hex

screws securing the seat support clamps to the camber bar.

2. Loosen, but do not remove the two (2) hex screws securing the frame clamps to the

camber bar.

3. Slide the camber bar through the clamps.

FIGURE 13 - REMOVING/INSTALLING THE CAMBER BAR

Seat Support

Clamp

Seat Support

Clamp

Frame Clamp

Socket

Screws

Socket

Screws

Camber Bar

SECTION 8

OPTIONS

OPTIONS

All manuals and user guides at all-guides.com

Summary of Contents for Top End Excelerator XLT

































































Reviews:

No comments