Invacare HMV Zoom 300 Service Manual Download Page 45

Page: 45 / 116

SECTION 8—TILLER

Part No 1122167

Zoom 300 and Zoom 400

2. Apply a thin coating of RTV sealant to the connectors.

3. Rotate the upper tiller shroud forward.

4. Secure the upper tiller shroud to the lower tiller shroud using the four (4) mounting

screws.

5. Perform one (1) of the following:

• On Zoom 300 - Connect the RED and BLACK controller connector to the RED and

BLACK battery connector. Refer to FIGURE 12.2 on page 87.

• On Zoom 400 - Connect the two (2) BLACK battery connectors to the wiring

harness connectors. Refer to FIGURE 12.3 on page 87.

6. Install the rear shroud. Refer to Removing/Installing the Rear Shroud on page 30.

7. Install the seat. Refer to Removing/Installing the Seat on page 19.

FIGURE 8.4

Removing/Installing the Upper Tiller Shroud

Mounting

Screws

Lower

Tiller

Shroud

Upper Tiller

Shroud

Lower Tiller

Shroud

Upper Tiller

Shroud

Throttle IDC

Tiller Harness

Connector

Headlight Connector to PC

Board (Zoom 400 only)

DETAIL “A”

Zoom 300

Shown

Zoom 400

Shown

Tiller

DETAIL “B”

Tiller Harness

connects

HERE

Headlight connects HERE

(Zoom 400 only)

Throttle IDC

connects HERE

Summary of Contents for HMV Zoom 300





















































































































Search results

Summary of Contents for HMV Zoom 300

Reviews:

Related manuals for HMV Zoom 300

Brands by name

Popular brands

Invacare HMV Zoom 300, Service Manual

Search results

Summary of Contents for HMV Zoom 300

Reviews:

Related manuals for HMV Zoom 300

Brands by name

Popular brands