manualshive.com logo in svg

Invacare HMV Zoom 300, Service Manual

Share
Download
Invacare HMV Zoom 300 Service Manual Download Page 38

SECTION 7—WHEELS AND CASTERS

Zoom 300 and Zoom 400

38

Part No 1122167

FIGURE 7.3   

Removing/Installing the Fork

Removing/Installing the Caster Assemblies

NOTE: For this procedure, refer to FIGURE 7.4.

Removing

1. Use a wrench to turn the hex nut on the caster assembly counter-clockwise to loosen 

and remove the caster wheel.

2. If necessary, repeat STEPS 1 to remove the other caster.

Installing

1. Insert the caster wheel into the caster housing and turn the hex nut clockwise to 

securely tighten the caster wheel in place.

FIGURE 7.4   

Removing/Installing the Caster Assemblies

Front Fork

Fork Stem 

Mount

Mounting Screws

Washers

Tiller Angle 

Adjustment Assembly

Scooter Frame

NOTE: Zoom 300 frame is shown. Front 
fork mounts the same way to Zoom 400.

Swingarm Assembly

Caster Housing

Hex Nut

Caster

Summary of Contents for HMV Zoom 300





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands