Invacare HMV Zoom 300 Service Manual Download Page 22

Page: 22 / 116

SECTION 4—SEAT

Zoom 300 and Zoom 400

Part No 1122167

Adjusting Seat Depth

WARNING

DO NOT adjust the seat position outside the specifications recommended by the

manufacturer. Otherwise, injury to user or damage to scooter may result.

NOTE: For this procedure, refer to FIGURE 4.5.

1. Remove the seat assembly from the scooter. Refer to Removing/Installing the Seat on

page 19.

2. Remove the adjustable width arms. Refer to Removing/Installing/Adjusting Arms on

page 25.

3. Remove the six (6) mounting screws located under the seat that secure the back

assembly to the seat base.

4. Adjust back assembly to one (1) of three (3) mounting positions.

5. Reinstall the six (6) mounting screws securing the back assembly to the seat base.

Securely tighten.

6. Reinstall the adjustable width arms. Refer to Removing/Installing/Adjusting Arms on

page 25.

7. Reinstall the seat assembly onto the scooter. Refer to Removing/Installing the Seat on

page 19.

NOTE: Mounting positions are in reverse order. For example, Depth-Low is the highest position.

FIGURE 4.5

Adjusting Seat Depth

Mounting

Screws

Back

Assembly

Seat Base

Mounting

Screws

Back

Assembly

Seat Base

Mounting Screws

Back

Assembly

Seat Base

Mounting

Screws

Back

Assembly

Seat Base

Mounting Positions

Mounting

Holes

Depth -

Low

Depth -

Medium

Depth -

High

Summary of Contents for HMV Zoom 300





















































































































Search results

Summary of Contents for HMV Zoom 300

Reviews:

Related manuals for HMV Zoom 300

Brands by name

Popular brands

Invacare HMV Zoom 300, Service Manual

Search results

Summary of Contents for HMV Zoom 300

Reviews:

Related manuals for HMV Zoom 300

Brands by name

Popular brands