Invacare HMV Zoom 300 Service Manual Download Page 106

Page: 106 / 116

SECTION 14—TRANSPORTING

Zoom 300 and Zoom 400

106

Part No 1122167

6. Perform the following to separate the front frame assembly from the rear frame

assembly:

A. Use the one hand to firmly hold the tiller handle.

B. Using the other hand, firmly hold the YELLOW frame lock lever [located under

marker label #

]and pull UP to the Unlocked position as shown in Detail “C” of

FIGURE 14.2.

NOTE: The frame lock lever remains in the unlocked position when the front frame assembly is
separated from the rear frame assembly.

C. Lift the front frame assembly so that the mounting brackets disengage from the

rear frame assembly as shown in Detail “C” of FIGURE 14.2.

D. Separate the front frame assembly from the rear frame assembly.

7. Fold tiller down to lowest locked position. Refer to Adjusting the Tiller Angle on

page 43.

Assembling

1. Unfold tiller. Refer to Adjusting the Tiller Angle on page 43.

2. Ensure that the tiller is in the highest locked position.

3. Perform the following to connect the front frame assembly to the rear frame assembly

(Detail “C” of FIGURE 14.2):

A. Use the one hand to firmly hold the tiller handle.

B. Using the other hand, firmly hold the front frame assembly and align with the

REAR frame assembly.

NOTE: The frame lock lever remains in the unlocked position when the front frame assembly is
separated from the rear frame assembly.

WARNING

When reassembling scooter, ensure the frame lock lever is in the LOCKED position

securing the FRONT and REAR frame assemblies together. Otherwise, injury and/

or damage may result.

C. Lower the front frame assembly so that the mounting brackets engage with the

rear frame assembly.

NOTE: The mounting brackets are engaged when an audible “click” is heard. The YELLOW frame
lock lever automatically locks in place.

4. Connect the 4-housing motor connector [located under marker label #

] to the

controller (Detail “B” of FIGURE 14.2).

5. Install the batteries. Refer to Removing/Installing the Batteries on Zoom 400 on

page 53.

6. Install the rear shroud. Refer to Removing/Installing the Rear Shroud on page 44.

Summary of Contents for HMV Zoom 300





















































































































Search results

Summary of Contents for HMV Zoom 300

Reviews:

Related manuals for HMV Zoom 300

Brands by name

Popular brands

Invacare HMV Zoom 300, Service Manual

Search results

Summary of Contents for HMV Zoom 300

Reviews:

Related manuals for HMV Zoom 300

Brands by name

Popular brands