manualshive.com logo in svg

Invacare HMV Zoom 300, Service Manual

Share
Download
Invacare HMV Zoom 300 Service Manual Download Page 111

SECTION 15—SCOOTER ACCESSORIES

Part No 1122167

111

Zoom 300 and Zoom 400

Installing/Removing the Safety Flag

 

WARNING

The installation of the safety flag onto the back of the scooter seat significantly 

increases the length of the scooter. When turning the scooter or swiveling the 

scooter seat, it is important to take note of this increased length - otherwise, injury 

and/or damage to the surrounding property may result.

NOTE: For this procedure, refer to FIGURE 15.4.

Installing

1. Install the bracket into the accessory tube located on the back of the seat.

2. Install mounting knob to secure the bracket in place. Securely tighten.

3. Install safety flag into bracket.

Removing

1. Remove the safety flag from the bracket.

2. Remove the mounting knob that secures the bracket in place.

3. Remove the bracket from the accessory tube located on the back of the seat.

FIGURE 15.4   

Installing/Removing the Safety Flag

Seat

Accessory Tube

Mounting Knob

Bracket

Safety Flag

Summary of Contents for HMV Zoom 300





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands