User’s Manual of NS3601-24P/4S Series
404
Switch IDs (1-16) are used to uniquely identify the switches within a stack. The Switch ID of each switch is shown on
the display on the front of the switch and is used widely in the web pages as well as in the CLI commands.
SyncE
SyncE Is an abbreviation for Synchronous Ethernet. This functionality is used to make a network 'clock frequency'
synchronized. Not to be confused with real time clock synchronized (IEEE 1588).
T
is an acronym for
T
erminal
A
cess
C
ontroller
A
ccess
C
ontrol
S
ystem
P
lus. It is a networking protocol which
provides access control for routers, network access servers and other networked computing devices via one or more
centralized servers. provides separate authentication, authorization and accounting services.
Tag Priority
Tag Priority is a 3-bit field storing the priority level for the 802.1Q frame.
TCP
TCP is an acronym for
T
ransmission
C
ontrol
P
rotocol. It is a communications protocol that uses the Internet Protocol
(IP) to exchange the messages between computers.
The TCP protocol guarantees reliable and in-order delivery of data from sender to receiver and distinguishes data for
multiple connections by concurrent applications (for example, Web server and e-mail server) running on the same
host.
The applications on networked hosts can use TCP to create connections to one another. It is known as a
connection-oriented protocol, which means that a connection is established and maintained until such time as the
message or messages to be exchanged by the application programs at each end have been exchanged. TCP is
responsible for ensuring that a message is divided into the packets that IP manages and for reassembling the packets
back into the complete message at the other end.
Common network applications that use TCP include the World Wide Web (WWW), e-mail, and File Transfer Protocol
(FTP).
TELNET
TELNET is an acronym for
TEL
etype
NET
work. It is a terminal emulation protocol that uses the Transmission Control
Protocol (TCP) and provides a virtual connection between TELNET server and TELNET client.
TELNET enables the client to control the server and communicate with other servers on the network. To start a Telnet
session, the client user must log in to a server by entering a valid username and password. Then, the client user can
enter commands through the Telnet program just as if they were entering commands directly on the server console.
TFTP
TFTP is an acronym for
T
rivial
F
ile
T
ransfer
P
rotocol. It is transfer protocol that uses the User Datagram Protocol (UDP)
and provides file writing and reading, but it does not provides directory service and security features.
ToS
ToS is an acronym for
T
ype
o
f
S
ervice. It is implemented as the IPv4 ToS priority control. It is fully decoded to
determine the priority from the 6-bit ToS field in the IP header. The most significant 6 bits of the ToS field are fully
decoded into 64 possibilities, and the singular code that results is compared against the corresponding bit in the IPv4
ToS priority control bit (0~63).
TLV
TLV is an acronym for
T
ype
L
ength
V
alue. A LLDP frame can contain multiple pieces of information. Each of these
pieces of information is known as TLV.
TKIP
TKIP is an acronym for
T
emporal
K
ey
I
ntegrity
P
rotocol. It used in WPA to replace WEP with a new encryption
algorithm. TKIP comprises the same encryption engine and RC4 algorithm defined for WEP. The key used for
encryption in TKIP is 128 bits and changes the key used for each packet.
Summary of Contents for GE-DSSG-244
Page 1: ...P N 1072570 REV 00 10 ISS 13JUN13 IFS NS3601 24P 4S GE DSSG 244 GE DSSG 244 POE User Manual ...
Page 10: ......
Page 38: ...IFS NS3601 24P 4S GE DSSG 244 and 244 POE User Manual 36 ...
Page 132: ...IFS NS3601 24P 4S GE DSSG 244 and 244 POE User Manual 130 Figure 4 8 1 Multicast Service ...
