background image

66

Before You Begin

Have the following items available:

The information that you recorded in Chapter 2, “Setting Up the Software.”

Windows NT operating system software CD-ROM, Windows NT Service Pack
CD-ROM, associated diskettes, and documentation.  Make sure you have the Setup
diskettes delivered with the operating system.

Backup diskettes you created according to instructions in Chapter 2, “Setting Up the
Software.”

Backup diskettes and documentation delivered with any expansion boards or additional
peripheral devices purchased from Intergraph Computer Systems.

The Late-Breaking News document delivered with the system.

You can find the system software on backup diskettes that you created, on diskettes provided
by Intergraph Computer Systems, or on the operating system CD-ROM.  If you did not create
backup diskettes of drivers or other system software products, they are probably available on
the operating system CD-ROM or on backup diskettes delivered with expansion boards.

NOTE

You must install certain drivers from backup or other diskettes.  The correct driver versions
may not be on CD-ROM.

Driver software is routinely improved and updated.  Visit the Intergraph Computer Systems
site on the World Wide Web and vendor bulletin boards for new and updated drivers.

Review the Late-Breaking News document delivered with your system for any additional
tasks you may have to perform during reinstallation.

Summary of Contents for TDZ 2000



































































































Reviews: