manualshive.com logo in svg

Interactive Technologies Commander 2000, Owner'S Manual, Page: 40 / 61

Share
Download
Interactive Technologies Commander 2000 Owner'S Manual Download Page 40

40

Enter 

ACCESS CODE + 8.

The panel and interior sirens sound one long beep, and the panel announces, 

Phone 

test is ON.

The system returns to level 1 when the phone test is complete. The panel announces, 

Phone test is OK, Alarm system is OFF.

If the panel announces, 

Phone test failure, Alarm system is OFF, 

make sure the panel 

is plugged into the phone jack. If a problem still exists, contact your security consult-
ant immediately.

■

To perform a sensor test:

1.

Enter 

ACCESS CODE + 9.

The panel and interior sirens sound one long beep, and the panel announces, 

Sensor 

test is ON.

 You have 15 minutes to complete the sensor test.

2.

Activate each sensor, as described in Table 9.
The panel and interior sirens sound several beeps, and the panel announces, 

Sensor 

[sensor #] OK

.

3.

Press 

STATUS 

when you think all sensors have been tested.

The panel announces, 

All sensors test OK

. If all sensors have not been tested, the 

panel announces a list of all untested sensors. Test all untested sensors.

4.

If you need more time to complete the sensor test, enter 

ACCESS CODE + 9.

This gives you 15 minutes to complete the sensor test, and you don’t have to retest 
any sensors.

5.

Enter 

ACCESS CODE + 1 

to exit the sensor test at any time.

or– The panel goes to level 1 after 15 minutes in sensor test, if you do not exit first.

The panel announces, 

Alarm system is OFF.

 

NOTE:

Performing a sensor test also clears the panel’s alarm history (see 
“Checking for Alarms” on page 36).

Technical Manuals Online! - http://www.tech-man.com

Summary of Contents for Commander 2000






























































Reviews:

No comments